Wahoo Fitness FAQs

Android This page contains firmware update notes for the KICKR BIKE: Wahoo's first Smart Bike featuring the most realistic ride feel around.

For installation, please see instructions for iOS or .

KICKR BIKE Firmware v1.4.0 - 26 November 2019

Added: Firmware support for new features

Added: Firmware support for improved remote diagnostics

Bug fixes for tilt calibration

KICKR BIKE Firmware v1.3.0 - 1 October 2019

Initial release

TICKR Troubleshooting

Most TICKR issues can be resolved by completing the following steps:

Replace the battery - data can fail to transmit properly on a low battery

Ensure pairing made only through app - if you've previously attempted to pair within your phone's Bluetooth settings (instead of through the Wahoo app or another app), unpair the TICKR through your phone's settings completely and retry pairing through the app.

Restart your phone - make sure you close out of all open apps before trying to reconnect

Wipe the pod with a moist cloth and hand wash the belt well with soap and water. Sweat and dirt buildup can cause connection errors.

Check the fit - ensure TICKR is worn snugly on the chest, directly against skin for the best connection (movement or slipping may disrupt readings). Always moisten the electrodes before use, as shown in the image below: Android Bluetooth Troubleshooting

Reset the TICKR -

Remove the battery

Flip the battery upside down and reinstall

Leave battery installed upside down for 3 seconds

Remove the battery and reinstall correctly

Replacethe battery cover

Check the battery connection - while the battery is removed, flex the metal prong that connects to the battery by pulling up gently. If the prong becomes pushed down too far, it can fail to make a strong connection with the battery.

Interference

If none of these resolves your issue and the LEDs are still functioning, you may be experiencing signal interference which can be caused by the following:

Previously paired apps or devices: The most common cause of interference is a previously paired app or device. It's important to unpair your TICKR from all other apps and devices (including previously paired computers, phones, watches, or the ELEMNT or ELEMNT BOLT, etc.), force stopping apps or shutting down additional devices before pairing with another.

Physical distance:Signal strength degrades as distance increases. For best results, keep your device less than 5 feet from your TICKR.

Wireless signals:Any devices that transmit wireless signals or electromagnetic fields can cause interference, especially these:

Wireless routers

Wireless or Bluetooth headphones or speakers

Wireless video receivers or transmitters (Chromecast, AirPlay, Roku, etc.)

Fans (especially large ones): avoid placing between your device and TICKR

Cordless home phones

Satellite or cable boxes

Microwave ovens

Power sources (power lines, boxes, lines in walls)

Wireless mice/keyboards

Certain TVs (especially WiFi Smart TVs) or monitors

Anything else that can transmit wireless signals, including radios and baby monitors

Physical barriers: Walls, metal desks, and counters all degrade signal quality.

If any of these are affecting your signal, try disabling or shutting down the offending devices. Alternatively, try relocating the TICKR further from the source of the interference or to a new environment completely.

You can also try resetting your wireless settings by selecting your device type below:

iOS Bluetooth Troubleshooting

If you're still having trouble, please contact support where we'll be happy to assist you further.

This page lists current and historical updates to the Wahoo Fitness App for iOS. For Android, see Wahoo Fitness App Updates (Android)

Wahoo Fitness App for iOS 5.25.3 - 6 December, 2019*

Fixed: Crash on migration

Fixed: Bug with switching workout profiles

Fixed: Bug that incorrectly set tilt limits on KICKR BIKE

*This release will roll out slowly to select users until full distribution on December 13, 2019.

Wahoo Fitness App for iOS 5.25.1 - 18 November, 2019*

Added: Access to Setup wizard from Linked Sensors page on Workout tab

Fixed: Bug causing crash during device onboarding

Fixed: HR time in zone updates during workout

Fixed: TICKR X Offline Workout sync (if you're still missing data, please contact support for further help)

Improved: KICKR BIKE user experience

Improved: Translations

*This release will roll out slowly to select users until full distribution on November 25, 2019.

Wahoo Fitness App for iOS 5.25.0 - 7 November, 2019*

Added: System Health Check - improves the view of linked sensors on the Workout Tab before starting a workout. Additional status information includes sensor data, firmware updates, and sensor errors. Tapping a sensor displays even more details.

Improved: Localizations for KICKR BIKE with focus on French and Italian

Improved: KICKR BIKE Fit from Photo on smaller devices

Fixed: Various UI issues on KICKR BIKE detail screen

Fixed: Stopped cells from sporadically reordering on the Workout tab Linked Sensors page

Fixed: Inability to update KICKR Headwind settings

Fixed: Cadence chart not updating on Indoor Cycling workout page

Fixed: Crash on updating KICKR CORE firmware

Fixed: inability to sync TICKR X offline workouts

Maintenance: General stability improvements

Note: This version of the Wahoo Fitness app only supports iOS 11 and later

*This release will roll out slowly to select users until full distribution on November 14, 2019.

Wahoo Fitness App for iOS 5.24.1 - 28 October, 2019*

Improved: KICKR BIKE Fit Tilt Offset

Fixed: Unable to toggle Control w/ ANT+ Power Meter

Fixed: Unable to toggle Erg Mode Speed Simulation

Fixed: Unable to toggle Erg Mode Power Smoothing

*This release will roll out slowly to select users until full distribution on November 4, 2019.

Wahoo Fitness App for iOS 5.24.0 - 2 October, 2019*

Added: Support for KICKR BIKE

Added: KICKR BIKE Fit features

Improved: Translation support

*This release will roll out slowly to select users until full distribution on October 9, 2019.

Wahoo Fitness App for iOS 5.23.1 - 20 September, 2019*

Stability Improvements

*This release will roll out slowly to select users until full distribution on September 27, 2019.

Wahoo Fitness App for iOS 5.23.0 - 17 September, 2019

Added: Support for iOS 13

Improved: Various translation improvements

Fixed: Single Arm Power Meter data doubled

Fixed: Circumference settings not impacting speed

Fixed: Issues with ANT+ connections

Fixed: HR level showing Peak 100% throughout workout

Fixed: Bug affecting Auto Pause

Fixed: Speed data recorded from multiple devices

Fixed: Speed displayed as N/A

Fixed: Speed/distance metrics not properly utilizing GPS

Fixed: Error exporting HR metrics

Fixed: Crash when paired with some Power Meters

Removed: Option to Login with Facebook

Note: This will be the last version to support iOS 10

Wahoo Fitness App for iOS 5.15.1 - August 6, 2019

Bug fixes and miscellaneous improvements

Wahoo Fitness App for iOS 5.15.0 - July 11, 2019*

Improved: Gradient changes on paired KICKR CLIMB

Improved: UI updates

Fixed: Profile not set to default power and heart rate zones when creating an account

Fixed: GPS file not recording if phone is locked during workout countdown

Fixed: No speed reading during outdoor workouts

Fixed: Calories during workout not matching calorie total in workout history

Fixed: 6 minute calibration for TICKR X fails

Fixed: Run graph's y axis should show steps, not strides

Fixed: Failure uploading workouts to Strava

Fixed: Workout summary route map anomalies

Fixed: HR zones resetting on app close

Fixed: HR level showing Peak 100% during workout

Fixed: App crashing when trying to share a workout in iOS 10

Fixed: App crashing when in background while loading workout detail graphs

Fixed: App crashing with RFLKT profile

*This release will roll out slowly to select users until full distribution on July 18, 2019.

Wahoo Fitness App for iOS 5.14.4 - May 20, 2019

Fixed: App crash on RFLKT pairing

Wahoo Fitness App for iOS 5.14.3 - May 15, 2019

Added: Workout profiles now default to heart rate page

Fixed: Various improvements to sensors setting screen

Fixed: KICKR speed readings not displaying

Fixed: Wheel circumference setting not affecting speed data

Fixed: Calibration for TICKR X showing values in imperial despite user profile in metric

Fixed: Various crashes and other bugs

Wahoo Fitness App for iOS 5.14.2 - April 30, 2019

FIXED: Elevation data not recording as expected

FIXED: Updated app icon for iPad

FIXED: Speed and distance not displaying indoors

FIXED: Workout history import failures

FIXED: Stages power meter calibration failures

FIXED: Missing speed/power/cadence from KICKR when connected via ANT+

FIXED: Distance and average pace discrepancies between workout details and history screens

FIXED: Various UI and stability issues

Wahoo Fitness App for iOS 5.14.0 - April 11, 2019*

All new look & feel to match our newest ELEMNT app

Account login - user profile info now syncs across Wahoo apps

New first launch wizard makes initial setup easier than ever

*Due to this update's size, release will be limited to small quantities until full distribution on April 18, 2019.

Wahoo Fitness App for iOS 5.13.3 - October 22, 2018

Support for new released iOS screens (iPhone XS, XS Max, XR)

Wahoo Fitness App for iOS 5.13.0 - July 10, 2018

Full KICKR CLIMB Support

Fixed a bug related to database migration

Fixed a bug not allowing negative slope on KICKR control page

Updated translations

Wahoo Fitness App for iOS 5.12.1 - May 2, 2018

FIXED: Unable to Change KICKR Control Settings on iPad

Other minor bug fixes

Wahoo Fitness App for iOS 5.12.0 - April 9, 2018

Added new cloud log in to sync details from other apps.

FIXED: Issue where the 'Done' and 'Cancel' buttons disappear after TICKR X calibration

FIXED: When pressing the Back button on the MyFitnessPal login screen, the app would remain on the "Authorizing account" page

Wahoo Fitness App for iOS 5.10.4 - March 14, 2018

FIXED: TCX Files unable to be uploaded to TrainingPeaks

FIXED: Cadence in TCX export file recorded as steps per minute, reading too high on Strava.

FIXED: Audio Announcements for time and pace

FIXED: Unable to change sensor name on main sensor page

FIXED: Calories not shown in workout history

FIXED: App crashes when trying to calibrate a RFLKT+ manually

FIXED: RideWithGPS uploads

FIXED : TICKR X workout start & end editing widgets

TWEAK: GPS accuracy no longer degrades speed and distance tracking. Note that dense tree cover can affect GPS accuracy.

Wahoo Fitness App for iOS 5.10.3 - February 12, 2018

Minor patch fix

Alert added for improper permission settings. This was causing GPS recording issues and failures to upload to Nike+

Wahoo Fitness App for iOS 5.10.2 - February 6, 2018

Bug Fix Release

FIXED: Crash when connecting to cloud server.

FIXED: Crash that sometimes occurred when attempting to sync TICKR X offline workouts.

FIXED: Crash that sometimes occurred when completing a workout

FIXED: Crash that occurred when restoring default settings

FIXED: Allow workouts to be uploaded in formats other than TCX

FIXED: Crash that sometimes happened when cancelling a KICKR calibration test

FIXED: Bug where sensors displayed repeatedly on iOS 9

FIXED: Crash that sometimes occurred in background when viewing detailedchart history

Wahoo Fitness App for iOS 5.10.1 - January 29, 2018

Updated the workout tracking to use FIT files for storing workout data.

Updated the workout history screens.

Paired sensors now connect earlier, even before entering the workout screen.

The app can now automatically select the best available data source from the available sensor

TICKR Fit support

iOS specific:

Fixes issue with incomplete data being synced to third party apps

Fixes issue with pairing sensors on iOS 9

Fixed offline sync from TICKR X

Other bug fixes

Wahoo Fitness App for iOS 5.10.0 - January 16, 2018

Updated for iPhone X

Bug Fixes

Wahoo Fitness App for iOS 5.9.10 - September 25, 2017

iOS 11 Compatibility

iPhone 8/8 Plus compatibility

Wahoo Fitness App for iOS 5.9.9 - July 26, 2017

Bug Fixes

Wahoo Fitness App for iOS 5.9.8 - July 19, 2017

Fix for connecting to Dropbox for sharing workouts.

Wahoo Fitness App for iOS 5.9.7 - July 19, 2017

Updated Dropbox api

Wahoo Fitness App for iOS 5.9.6 - May 23, 2017

Bug fixes

Wahoo Fitness App for iOS 5.9.7 - February 14, 2017

Today Plan Uploads

Bug fixes

Wahoo Fitness App for iOS - Previous Updates

5.9.2 - Nov 16, 2016

Fix for RFLKT and ECHO screen updates

5.9.1 - Nov 11, 2016

Unfortunately, Garmin Connect is no longer accepting uploads from non Garmin devices and apps. We have therefore removed support for this share site.Disabled support for importing workouts from Garmin WatchesImproved KICKR support and fixed a couple registration issues

5.8.1 - Aug 3, 2016

Minor bug fixes.Go Team Sky!

5.8.0 - Jul 25, 2016

- Updated sensor compatibility.

5.7.7 - Mar 16, 2016

Support for Wahoo Speed

5.7.6 -Jan 6, 2016

GPS FixesKICKR Registration fixes

5.7.5 -Dec 1, 2015

Bug fixes and improvements.

5.7.4 -Nov 19, 2015

Support for updates to the Wahoo RFLKT bike computer

5.7.2 -Oct 28, 2015

- Fix for Nike+ uploads- Fix for KICKR Snap updates- Fix for a few crash reports

5.7.1 -Oct 21, 2015- Better iOS 9 support- Fix crashes on long rides- Fix GPS dropouts

5.7.0 -Sep 16, 2015iOS 9 Support

5.6.1 -Jul 14, 2015Fix for Timex watchFix for iOS update

5.6.0 -Jun 10, 2015- Fixed TICKR Smoothness issues- Fixed Nike+ Upload issuesk+ Performance tweaks.

5.5.2 -Apr 20, 2015- Improvements to TIMEX Support- Fixed crash in history for long workouts- Fixed treadmill uploads to Nike+- Only show Nike+ Fuel if linked accounts- Fixed power data upload issue/display- Fixed issue in CSV data/time

5.5.1 - Mar 17, 2015+ Nike+ FUEL In workout / History+ Nike+ Workout upload+ 64bit SupportBug fixes and improvementsPlease remember to update your reviews for the latest version. Thanks :-)

5.5.0 - Mar 9, 2015+ Nike+ FUEL In workout / History+ Nike+ Workout upload+ 64bit SupportBug fixes and improvements

This page lists current and historical updates to the Wahoo Fitness App for Android. For iOS, see Wahoo Fitness App Updates (iOS)

Wahoo Fitness App for Android 1.25.3.1 - 6 December, 2019*

Fixed: Bug that incorrectly set tilt limits on KICKR BIKE

*This release will roll out slowly to select users until full distribution on December 13, 2019.

Wahoo Fitness App for Android 1.25.1.4 - 19 November, 2019*

Fixed: Crash on startup with Android 5.1

Fixed: TICKRX reporting Cadence on Indoor Run

Minor bug fixes and miscellaneous improvements

Note: This is the last version of the Wahoo Fitness app that will support Android 5.1

*This release will roll out slowly to select users until full distribution on November 26, 2019.

Wahoo Fitness App for Android 1.25.0.72 - 7 November, 2019*

Added: System Health Check - improves the view of linked sensors on the Workout Tab before starting a workout. Additional status information includes sensor data, firmware updates, and sensor errors. Tapping a sensor displays even more details.

Removed: Burn and Burst workout page from all workout profiles

Fixed: Inability to update KICKR Headwind settings

Improved: Bike Fit Wizard

Improved: Logs from failed firmware updates

Improved: Status Bar UI Updates

Improved: KICKR BIKE Fit Tilt Offset

*This release will roll out slowly to select users until full distribution on November 14, 2019.

Wahoo Fitness App for Android 1.24.1.3 - 28 October, 2019*

Improved: KICKR BIKE Fit Tilt Offset

*This release will roll out slowly to select users until full distribution on November 4, 2019.

Wahoo Fitness App for Android 1.24.0.29 - 2 October, 2019*

Added: Support for KICKR BIKE

Added: KICKR BIKE Fit features

Fixed: Issues with registering KICKR CORE

Fixed: Issues with changing CLIMB wheelbase

Fixed: Issues with changing workout types with TICKR X

Fixed: Issues with level mode over ANT+ FE-C

Fixed: Crash when adjusting heart rate zones on Headwind

*This release will roll out slowly to select users until full distribution on October 9, 2019.

Wahoo Fitness App for Android 1.23.0.17 - 17 September, 2019*

Bug fixes and miscellaneous improvements

Fixed: Crash when paired with some Power Meter

Removed: Option to login with Facebook

*This release will roll out slowly to select users until full distribution on September 24, 2019.

Wahoo Fitness App for Android 1.15.0.117 - July 31, 2019

Bug fixes and miscellaneous improvements

Wahoo Fitness App for Android 1.15.0.113 - July 9, 2019*

Improved: Notification management

Improved: Onboarding process

Improved: Crash stability

FIXED: Inability to set and save wheel circumference

FIXED: App unable to maintain connection with KICKRs

FIXED: Inconsistent units of measure across workout pages

FIXED: Inability to rename sensors

FIXED: Deleted workouts still syncing to 3rd party apps

*This release will roll out slowly to select users until full distribution on July 16, 2019.

Wahoo Fitness App for Android 1.14.1.15 - June 13, 2019*

Improved crash reporting

*This release will roll out slowly to select users until full distribution on June 20, 2019.

Wahoo Fitness App for Android 1.14.1.10 - May 14, 2019*

Feature: Added Heart Rate page as default for all workout profiles

Feature: Added option to set wheel circumference

FIXED: "About You" section of Profile page now saves first and last name on edit

FIXED: Left/right power reporting

*This release will roll out slowly to select users until full distribution on May 21, 2019.

Wahoo Fitness App for Android 1.14.1.3 - April 30, 2019

FIXED: Blank workout page after finishing an activity

FIXED: Inability to set wheel circumference

FIXED: Garmin Vector 3 power meter pairing label

FIXED: Various stability issues

Wahoo Fitness App for Android 1.14.0.299 - April 11, 2019*

All new look & feel to match our newest ELEMNT app

Account login - user profile info now syncs across Wahoo apps

New first launch wizard makes initial setup easier than ever

*Due to this update's size, release will be limited to small quantities until full distribution on April 18, 2019.

Wahoo Fitness App for Android 1.13.0.94 - July 12, 2018

FIXED: app freeze on device detail page when connected to KICKR CLIMB

FIXED: reporting of select KICKR CLIMB details

Wahoo Fitness App for Android 1.13.0.88 - July 10, 2018

Full KICKR CLIMB Support

Fixed a bug causing spindowns to fail

Fixed a bug causing users to not see running analytics when viewing workout history

Wahoo Fitness App for Android 1.12.0.15 - April 9, 2018

FIXED: Issue where Burn and Burst data was no longer showing on workout results page

FIXED: Issue causing incorrect heart rate data to be exported via CSV

ADDED: Auto pause!

Wahoo Fitness App for Android 1.10.5.3 - February 12, 2018

FIXED: KICKR registration functionality bug

FIXED: CSV export option bug

FIXED: Minor crash fixes

Wahoo Fitness App for Android 1.10.0.21 - January 29, 2018

Updated the workout tracking to use FIT files for storing workout data.

Updated the workout history screens.

Paired sensors now connect earlier, even before entering the workout screen.

The app can now automatically select the best available data source from the available sensor

TICKR Fit support

Yes, the ELEMNT Bolt is compatible with muscle oxygen sensors that transmit over the standard ANT+ Muscle Oxygen Sensor protocol including BSXInsight, Moxy, and Humon Hex sensors.

The ELEMNT Bolt displays the following measurements from your muscle oxygen sensor:

Displays the current Saturated Hemoglobin (oxygenated hemoglobin) as a percentage.

Displays the current Total Hemoglobin (saturated + unsaturated levels) as measured in grams per decilitre.

Displays the Minimum amount of Saturated Hemoglobin detected during your workout or lap.

Displays the Average amount of Saturated Hemoglobin detected during your workout or lap.

Displays the Maximum amount of Saturated Hemoglobin detected during your workout or lap.

Displays the Minimum amount of Total Hemoglobin detected during your workout or lap.

Displays the Average amount of Total Hemoglobin detected during your workout or lap.

Displays the Maximum amount of Total Hemoglobin detected during your workout or lap.

Acronyms/Symbol Explanation:

tHb: Total Hemoglobin Concentration: Total hemoglobin in the blood (saturated + unsaturated).

SmO2: Saturated Hemoglobin Percentage: Current percentage of hemoglobin saturated with oxygen.

Yes, the ELEMNT Bolt is compatible with muscle oxygen sensors that transmit over the standard ANT+ Muscle Oxygen Sensor protocol including BSXInsight, Moxy, and Humon Hex sensors.

The ELEMNT displays the following measurements from your muscle oxygen sensor:

Displays the current Saturated Hemoglobin (oxygenated hemoglobin) as a percentage.

Displays the current Total Hemoglobin (saturated + unsaturated levels) as measured in grams per decilitre.

Displays the Minimum amount of Saturated Hemoglobin detected during your workout or lap.

Displays the Average amount of Saturated Hemoglobin detected during your workout or lap.

Displays the Maximum amount of Saturated Hemoglobin detected during your workout or lap.

Displays the Minimum amount of Total Hemoglobin detected during your workout or lap.

Displays the Average amount of Total Hemoglobin detected during your workout or lap.

Displays the Maximum amount of Total Hemoglobin detected during your workout or lap.

Acronyms/Symbol Explanation:

tHb: Total Hemoglobin Concentration: Total hemoglobin in the blood (saturated + unsaturated).

SmO2: Saturated Hemoglobin Percentage: Current percentage of hemoglobin saturated with oxygen.

To get accurate results from a speed sensor like the Wahoo RPM Speed or Blue SC, input your wheel circumference in the Wahoo Fitness App. An accurate speed sensor can also improve the accuracy of GPS Bike Computers like the ELEMNT, ELEMNT ROAM, and ELEMNT BOLT, especially in tree cover or near buildings.

You can find tire size on the side of your tires. Tire circumference may vary depending on tire pressure. Properly inflate your tires for the most accurate results.

Please see Setting Up Wheel Circumference for detailed instructions and additional information.

Tire Size

Circumference in Meters

Circumference in mm

ISO

700 x 18C

2.07

2070

18-622

700 x 19C

2.08

2080

19-622

700 x 20C

2.086

2086

20-622

700 x 23C

2.096

2096

23-622

700 x 25C

2.105

2105

25-622

700C Tubular

2.13

2130

700 x 28C

2.136

2136

28-622

700 x 30C

2.146

2146

30-622

700 x 32C

2.155

2155

32-622

700 x 35C

2.168

2168

35-622

700 x 38C

2.18

2180

38-622

700 x 40C

2.2

2200

40-622

700 x 44C

2.235

2235

44-622

700 x 45C

2.242

2242

45-622

700 x 47C

2.268

2268

47-622

650 x 20C

1.938

1938

20-571

650 x 23C

1.944

1944

23-571

650 x 35A

2.09

2090

37-590

650 x 38B

2.105

2105

40-584

650 x 38A

2.125

2125

40-590

12" x 1.75"

0.935

0935

47-203

12" x 1.95"

0.94

0940

54-203

14" x 1.50"

1.02

1020

40-254

14" x 1.75"

1.055

1055

47-254

16" x 1.50"

1.185

1185

40-305

16" x 1.75"

1.195

1195

47-305

16" x 2.00"

1.245

1245

54-305

16" x 1-1/8"

1.29

1290

28-349

16" x 1-3/8"

1.3

1300

37-349

18" x 1.50"

1.34

1340

40-355

18" x 1.75"

1.35

1350

47-355

20" x 1.25"

1.45

1450

32-406

20" x 1.35"

1.46

1460

35-406

20" x 1.50"

1.49

1490

40-406

20" x 1.75"

1.515

1515

47-406

20" x 1.95"

1.565

1565

50-406

20" x 1-1/8"

1.545

1545

28-451

20" x 1-3/8"

1.615

1615

37-451

22" x 1-3/8"

1.77

1770

37-501

22" x 1-1/2"

1.785

1785

40-501

24" x 3/4" Tubular

1.785

1785

24" x 1"

1.753

1753

25-520

24" x 1-1/8"

1.795

1795

28-540

24" x 1-1/4"

1.905

1905

32-540

24" x 1.75"

1.89

1890

47-507

24" x 2.00"

1.925

1925

50-507

24" x 2.125"

1.965

1965

54-507

26" x 7/8" Tubular

1.92

1920

26" x 1.25"

1.95

1950

32-559

26" x 1.40"

2.005

2005

37-559

26" x 1.50"

2.01

2010

40-559

26" x 1.75"

2.023

2023

47-559

26" x 1.95"

2.05

2050

50-559

26" x 2.00"

2.055

2055

52-559

26" x 2.1"

2.068

2068

54-559

26" x 2.125"

2.07

2070

57-559

26" x 2.35"

2.083

2083

58-559

26" x 3.00"

2.17

2170

75-559

26" x 1-1.0"

1.913

1913

25-559

26" x 1"

1.952

1952

25-571

26" x 1-1/8"

1.97

1970

28-590

26" x 1-3/8"

2.068

2068

37-590

26" x 1-1/2"

2.1

2100

37-584

27" x 1"

2.145

2145

25-630

27" x 1-1/8"

2.155

2155

28-630

27" x 1-1/4"

2.161

2161

32-630

27" x 1-3/8"

2.169

2169

37-630

27.5" x 1.50"

2.079

2079

40-584

27.5" x 1.95"

2.09

2090

50-584

27.5" x 2.10"

2.148

2148

54-584

27.5" x 2.25"

2.182

2182

57-584

29" x 2.25"

2.281

2281

58-622

29" x 2.1"

2.288

2288

54-622

29" x 2.2"

2.298

2298

56-622

29" x 2.3"

2.326

2326

60-622

iOS/iPhone

ELEMNT GPS Bike Computers are designed to work with any Apple device on iOS 11 or newer. To check the iOS version of your Apple device, please see Find the software version on your iPhone, iPad, or iPod.

Android

ELEMNT GPS Bike Computers are designed to work with mostBluetoothcompliant Android devices running Android version 6 ornewer which allow 3rd party app access to Bluetooth.

Note: Since Android devices vary widely, compatibility cannot be assured for all devices. Please download and install the Wahoo Fitness Android app from the Google Play Store before purchasing a Wahoo Fitness product to ensure compatibility.

IMPORTANT: This page covers installation of the Campagnolo Freehub on KICKR '18 and KICKR CORE.

Please see instructions for KICKR '14 and '16 if installing on these trainers.

mount your bike

KICKR '18 & KICKR CORE Campagnolo Freehub Compatibility

The KICKR '18 & KICKR CORE Campagnolo Freehub is compatible with both Campagnolo, SRAM, and Shimano cassettes made in 2010 or newer

Campagnolo cassettes with 8 inner arms on the largest cog are NOT compatible (see image below)

Installation on KICKR '18 & CORE

Required Tools:

Sprocket remover (AKA chain whip) or chain vice (as pictured in instructions below)

17mm cone wrench or crescent wrench (adjustable wrench also acceptable)

Cassette lockring tool (we recommend either the Park Tool FR-5.2 or similar, or Park Tool BBT-5/FR-11 if using the Campagnolo lockring which came with your cassette - see note below next image for details) and matching1" (25.4 mm) socket wrench or adjustable wrench

Included Components:

Notes:

The Campy freehub supports Campagnolo, Shimano, and SRAM cassettes, but included spacers are not needed with Campagnolo cassettes.

For your convenience, the included lockrings are geared for use with Shimano/SRAM lockring tools like the Park Tool FR-5.2.

Alternatively, you may use the lockring included with your cassette (both Shimano/SRAM and Campy compatible lockrings are supported).

Installation Steps:

Start by using the chain whip (or chain vice, as pictured) and lockring tool to loosen the lockring and remove the existing cassette (skip this step if a cassette is not present, like in KICKR CORE initial setup).

Use the 17mm cone wrench to remove the existing original lock nut and freehub body. Hold the pulley with your free hand for stability.

Install the inner spacer. You can use either the spacer contained in the Campagnolo freehub (ships on the inside of the side with the pawls) or the original inner spacer. While cosmetically different (the Campy freehub's is shiny), they remain mechanically identical. Do not use both.

Check the center of the Campagnolo freehub for any overhang on the captive inner spacer. Adjust this spacer by hand to ensure it's flush all around, as shown below:

Install the new Campagnolo freehub over the inner spacer, rotating counterclockwise (in the direction of the pawls) until flush against the pulley.

Screw on the original lock nut and tighten with the 17mm cone wrench, again holding the pulley with your other hand for stability. Tighten until snug, being sure to avoid applying excessive force.

Install the included spacer as needed for your cassette, along with any other spacers which came included with the cassette.

Install your cassette on the freehub like shown in the video below (instructions start at 1:20):

You're now ready to and get KICKN!

How Do I Update KICKR HEADWIND?

This page contains current and historical firmware update notes for KICKR HEADWIND. For installation instructions, please see

KICKR HEADWIND Firmware v1.0.3 - 2 December 2019

Added support for Bluetooth Multi Peripheral (allows connections for up to 3 devices)

KICKR HEADWIND Firmware v1.0.2 - 9 September 2018

Direct ANT+ control

Added support for Heart Rate and Speed mode standby states: after 3 minutes of inactivity the fan and LED lights are powered off. Power resumes when the last paired sensor is in range and activated, allowing the sensor to start and power down KICKR HEADWIND without touching a button.

KICKR HEADWIND Firmware v1.0.0 - 27 June 2018

Initial release

Android System Requirements:

Android version 6 or newer

Bluetooth 4.0 (Smart) or newer

Third party app access to Bluetooth

Compatible Devices:

Most Android devices running Android 6 or newer with Bluetooth 4.0 will work. However, Wahoo Fitness has not tested complete compatibility with all devices. Please download the Companion App from the Google Play Store to ensure that it installs on your device before purchasing a product.

As a Heart Rate Monitor, TICKR X works with numerous ANT+ and Bluetooth 4.0 compatible devices and apps. However the following features are available ONLY via Bluetooth 4.0 on the iPhone 4s or newer and Android phones on Android 6 or newer exclusively in the Wahoo Fitness App:

Offline Workouts - Will give you heart rate, workout duration, and calories burned

Treadmill Mode (Will not work during offline workouts)

Running Smoothness (Will not work during offline workouts)

Indoor Cycling Mode (Will not work during offline workouts)

See the following links to learn more about Wahoo Fitness App Compatibility for iOS or Android.

KICKR HEADWIND pairs to the Wahoo Fitness App on iOS and Android mobile devices via Bluetooth, or connects directly to ANT+ enabled heart rate monitors like the Wahoo TICKR, speed sensors like the Wahoo RPM Speed, and trainers like all Wahoo Smart Trainers or other ANT+ enabled third party trainers.

Bluetooth Devices:

Apple iOS devices on iOS 10 or newer

Android devices running Android 6 or newer

Trainers & Sensors:

ANT+ enabled heart rate monitors like the Wahoo TICKR

ANT+ enabled speed sensors like the Wahoo RPM Speed

All Wahoo Smart Trainers

ANT+ enabled third party trainers

The Wahoo RPM Speed Sensor allows you to track and monitor your speed on iOS and Android smartphones as well as GPS cycling computers.

iOS: This product is designed for use on iOS devices running iOS 10 or newer.

Android: This product is designed for use with Android devices compliant with Bluetooth 4.0 running Android 6 or newer.

Due to the wide range of Android devices, compatibility cannot be guaranteed for all devices matching these descriptions. Please download the Wahoo app from the Google Play Store before purchase to ensure compatibility with a specific device.

Cycling Computers: This product is designed for use on most cycling computers which accept ANT+ and/or Bluetooth 4.0 connections or newer.

The accessories required for the KICKR SNAP depend on use. To start, the KICKR SNAP must be plugged in to provide resistance so you'll at least need access to an electrical outlet.

If you're uninterested in speed or power data and just want resistance alone, you'll only need:

A compatible bicycle (see: compatible bikes )

To get power and speed readings from the KICKR SNAP, you'll need:

A compatible bicycle(see: compatible bikes )

A compatible iOS or Android Bluetooth enabled device to read data

For the ultimate experience (full data monitoring and resistance control) you'll need the following:

A compatible bicycle(see: compatible bikes )

A device to control the KICKR. These devices include:

iPhone, iPad or other iOS device on iOS 11 (or newer)

Mac Computer with Bluetooth 4.0 (or newer)

Computer with ANT+ USB dongle (compatibility varies by software platform; check individual websites for compatibility)

Android device on Android 6 (or newer) with Bluetooth (see: compatible devices )

An RPM/Cadence sensor such as the RPM or BLUE SC.

A heart rate sensor like our TICKR X.

Note: the KICKR SNAP can be controlled with ANT+ or Bluetooth devices (KICKR firmware version 1.1.2 and newer) but can only be updated via Bluetooth from iOS and Android devices.

This page describes how to update firmware from an Android device. For iOS devices, please see How to Update KICKR CLIMB Firmware? (iOS). Note: KICKR CLIMB firmware can only be updated from iOS or Android devices.

Wahoo updates your KICKR CLIMB's firmware (a kind of software) frequently to deliver the best indoor training experience possible. Ensuring you have the latest firmware resolves many issues, keeping you climbing at your best.

Requirements:

ABluetoothenabled Android device on Android 6 or newer

Your Android device actively connected to the internet over WiFi

The newest version of the Wahoo Utility app (please check for updates in the Play store)

Your KICKR or KICKR SNAP on the latest firmware ( instructions here )

Update Steps:

Ensure Bluetooth and location services are enabled in your Android settings and that your device is within 5 feet of the KICKR CLIMB, then follow these steps to pair:

With the Wahoo Utility app (note: not to be confused with the Wahoo Fitness app) open and the KICKR CLIMB powered on, find the KICKR CLIMB on the default "Discover Devices" page. Tap to connect once it appears. signal interference article

Please be patient as the KICKR CLIMB can take up to 90 seconds to connect. Once connected, the app will show the firmware version and the option to Upgrade Firmware, as shown above.

Tap Upgrade Firmware then Yes to start the update process.

Leave your Android device near the KICKR CLIMB until the update is complete. If the update fails, restart the process by fully closing and reopening the Wahoo Utility app. You may also need to reboot the KICKR CLIMB itself by disconnecting the power for 30 seconds, then reconnecting it.

Once notified the firmware upgrade is complete, just fully close the Wahoo Utility app (to prevent any possible interference) and your KICKR CLIMB is ready to ride! Simply pair with the KICKR ( instructions here ) and start a workout in the Wahoo Fitness app using the grade controls on the KICKR Control Page (available by swiping right during a workout). Your KICKR CLIMB is also ready to use in supported third party apps, if preferred. Since the CLIMB pairs with your KICKR, you need only pair the KICKR to a third party app and ensure your CLIMB is in unlocked mode to experience physical elevation changes as you ride!

If issues updating persist, please take a look at our to eliminate possible conflicts with other devices and try again.

BASIC TICKR INFO

The Wahoo TICKR is a heart rate monitor intended for use with your iOS or Android smartphone or tablet device, or even your GPS watch. In conjunction with your device, it uses Bluetooth 4.0 and ANT+ technology to track heart rate, calories burned, time, plus distance and pace information.

iOS: This product is designed for use on devices running iOS 10 or newer

Android: This product is designed for use with Android devices compliant with the Bluetooth 4.0 protocol running version 6 or newer & must allow Third Party App Access to the Bluetooth 4.0 (Smart) Radio

NOTE: Wahoo Fitness has not tested complete compatibility with all Android devices matching this description. Please download the app from the Google Play Store to ensure that it installs on your device before purchasing a product.

This product is shipped with the following:

Heart Rate Monitor

Adjustable soft strap

CR 2032 Battery (installed)

Quick Start Guide

Important Product Info Guide

Design Specifications:

Physical Dimensions (LxWxH): 2.755"x1.5" (7cmx1.3cmx3.8cm)

Weight: 1/3 oz (8.5 grams) without strap

Battery: CR2032

Battery Life: Up to 12 months

Sweat Proof: Yes (hand washable strap)

Water Rating: IPX7 (waterproof up to 5 ft/1.5m)

Strap Length: Adjustable from 24" to 48 (61-122cm) stretched

This page provides instructions for pairing the KICKR or KICKR SNAP with Apple devices running iOS 10 or newer. Instructions for pairing with Android devices on 6 or newer are available here.Follow these steps to pair your KICKR with the Wahoo Fitness app:

Plug in your KICKR Power Trainer to ensure it's on and ready to pair

Make sure Bluetooth is enabled on your device

Open the Wahoo Fitness app after installing from the Apple App Store

Select Sensors in the bottom left corner, thenAdd New Sensor

Choose your KICKR from the list of available sensors

If this is your first time pairing, take a moment to register your KICKR. If prompted, update your firmware as well to enjoy the smoothest ride possible. Lastly, you'll need to perform a spindown to calibrate your KICKR on first use and once every 2 weeks after.

Once complete, with the KICKR sensor page still open select Save Sensor

Choose the workout profiles you would like your KICKR active for (ex. Indoor Cycling), then select Done" to save the device for later.

Your KICKR is now paired and ready for action! To use your KICKR, start a workout in one of the profiles you marked the KICKR active for. Swipe right within a workout to access detailed KICKR controls and workout modes. For more details on workout modes see What Are the Different Modes on My Smart Trainer?

Since the Wahoo Fitness app remembers saved devices, you can avoid the sensors page and simply start a new workout next time to get kickin!

For additional setup help, see the Wahoo KICKR Information and Setup page.

This page provides instructions for pairing the KICKR or KICKR SNAP with Android devices on 6 or newer. Instructions for pairing withApple devices running iOS 10 or newer are available here.Follow these steps to pair your KICKR or Snap with the Wahoo Fitness app:

Plug in your KICKR and ensure Bluetooth and location services are enabled on your device

Open the Wahoo Fitness app after installing it from the Google Play Store, then select Sensors in the top right What Are the Different Modes on My Smart Trainer?

On the next screen, select the + icon in the top right to search

Choose your KICKR from the list of available sensors

If this is your first time pairing, take a moment to register your KICKR. You'll need to perform a spindown to calibrate your KICKR on first use and every 2 weeks after. It's important to update your KICKR as well by following these instructions.

When finished, select Save device

Choose the workout profiles your KICKR will be active for (ex. Indoor Cycling), then save

Your KICKR is now paired and ready for action! To use your KICKR, start a workout in one of the profiles you marked the KICKR active for. Swipe right within a workout to access detailed KICKR controls and workout modes. For more details on workout modes see

Since the Wahoo Fitness app remembers saved devices, you can avoid the sensors page and simply start a new workout next time to get kickin' fast!

iOS: The ELEMNT is designed to work with any Apple device on iOS 10.0 or newer. To check the iOS version of your Apple device, please see Find the software version on your iPhone, iPad, or iPod.

Android: The ELEMNT is designed to work with mostBluetoothcompliant Android devices running Android version 6 ornewer which allow 3rd party app access to Bluetooth.

Note: Since Android devices vary widely, compatibility cannot be assured for all devices. Please download and install the Wahoo Fitness Android app from the Google Play Store before purchasing a Wahoo Fitness product to ensure compatibility.

The accessories required for the KICKR depend on use. To start, the KICKR must be plugged in to provide resistance so you'll at least need access to an electrical outlet.

If you're uninterested in speed or power data and just want resistance alone, you'll only need:

A compatible bicycle (see: compatible bikes )

To get power and speed readings from the KICKR, you'll need:

A compatible bicycle(see: compatible bikes )

A compatible iOS or Android Bluetooth enabled device to read data

For the ultimate experience (full data monitoring and resistance control) you'll need the following:

A compatible bicycle(see: compatible bikes )

A device to control the KICKR. These devices include:

Apple devices running iOS 10 or newer

Android device on Android 6 or newer with Bluetooth (see: compatible devices )

Mac computers with built in Bluetooth 4.0

Windows PCs with an ANT+ USB dongle (compatibility varies by software platform - check individual websites for compatibility)

An RPM/Cadence sensor (included with KICKR, or the RPM or BLUE SC ).

A heart rate sensor like our TICKR X.

Note: the KICKR can be controlled with ANT+ or Bluetooth devices (KICKR firmware version 1.1.2 and newer) but can only be updated via Bluetooth.

BASIC TICKR INFO

The Wahoo TICKR Run is a heart rate monitor intended for use with your iOS or Android smartphone or tablet device, or even your GPS watch. In conjunction with your device, it uses Bluetooth 4.0 and ANT+ technology to track heart rate, calories burned, time, plus distance and pace information. The TICKR Run has been optimized for runners and also monitors your running form in three dimensions, alongside other key running indicators such as cadence, vertical oscillation and ground contact time.

iOS: This product is designed for use on the Apple devices running iOS 10 and newer

Android: This product is designed for use with Android devices compliant with the Bluetooth 4.0 protocol running version Android 6 or newer & must allow Third Party App Access to the Bluetooth 4.0 (Smart) RadioNote: Wahoo Fitness has not tested complete compatibility with all Android devices matching this description. Please download the app from the Google Play Store to ensure that it installs on your device before purchasing a product.

This product is shipped with the following:

Heart Rate Monitor

Adjustable soft strap

CR 2032 Battery (installed)

Quick Start Guide

Important Product Info Guide

Design Specifications:

Physical Dimensions (LxWxH): 2.755"x1.5" (7cmx1.3cmx3.8cm)

Weight: 1/3 oz (8.5 grams) without strap

Battery: CR2032

Battery Life: Up to 12 months

Sweat Proof: Yes (hand washable strap)

Water Rating: IPX7 (waterproof up to 5 ft/1.5m)

Strap Length: Adjustable from 24" to 48 (61-122cm) stretched

The Wahoo TICKR is a heart rate monitor intended for use with your iOS or Android smartphone or tablet device, or even your GPS watch. In conjunction with your device, it uses Bluetooth 4.0 and ANT+ technology to track heart rate, calories burned, time, plus distance and pace information.

iOS: This product is designed for use on the Apple devices running iOS 10 and newer

Android: This product is designed for use with Android devices compliant with the Bluetooth 4.0 running version Android 6 or newer which allow Third Party App Access to Bluetooth 4.0Note: Wahoo Fitness has not tested complete compatibility with all Android devices matching this description. Please download the app from the Google Play Store to ensure that it installs on your device before purchasing a product.

This product is shipped with the following:

Heart Rate Monitor

Adjustable soft strap

CR 2032 Battery (installed)

Quick Start Guide

Important Product Info Guide

Design Specifications:

Physical Dimensions (LxWxH): 2.755"x1.5" (7cmx1.3cmx3.8cm)

Weight: 1/3 oz (8.5 grams) without strap

Battery: CR2032

Battery Life: Up to 12 months

Sweat Proof: Yes (hand washable strap)

Water Rating: IPX7 (waterproof up to 5 ft/1.5m)

Strap Length: Adjustable from 24" to 48 (61-122cm) stretched

Additional information is available on the Heart Rate Monitor product page

CHOOSE THE RIGHT TICKR FOR YOUR WORKOUT

Buy

TICKRFIT

TICKR

TICKRX

Buy

Reg: $79.99

Buy

Reg: $49.99

Reg: $79.99

SPECIFICATIONS

Heart Rate Sensor

Optical

ECG

ECG

Unit Dimensions (L x W x H)

1.75" x 1.25" x 0.5"

2.75" x 1.5" x 0.5"

2.75" x 1.5" x 0.5"

Weight

12 grams without strap

8.5 grams without strap

8.5 grams without strap

Battery

Rechargeable Lithium Ion

Coin Cell (CR2032)

Coin Cell (CR2032)

Battery Life

Up to 30 hours

Up to 1 year

Up to 1 year

Strap Type

Arm

Chest

Chest

Strap Size Range

Small 10" x 1" (260mm x 25.4mm) Large 15" x 1" (375mm x 25.4mm)

23" to 48"

23" to 48"

Water Rating

IPX7 (Waterproof up to 5 ft)

IPX7 (Waterproof up to 5 ft)

IPX7 (Waterproof up to 5 ft)

Washable Strap

Yes

Yes

Yes

On/Off Button

Yes

No

No

Accelorometer

Yes

Yes

Yes

CONNECTIVITY

Wireless Connectivity

BLUETOOTH Low Energy and ANT+

BLUETOOTH Low Energy and ANT+

BLUETOOTH Low Energy and ANT+

Wireless Signal Strength

Up to 10 feet

Up to 10 feet

Up to 10 feet

Phone Compatibility

iPhone and Android

iPhone and Android

iPhone and Android

Third Party App Compatibility

Yes

Yes

Yes

FEATURES

LED Indicator Lights

Yes

Yes

Yes

Heart Rate Tracking

Yes

Yes

Yes

Calorie Tracking

Yes

Yes

Yes

Workout Duration Tracking

Yes

Yes

Yes

Running Analytics

No

No

Cadence, Ground Contact Time, Vertical Oscillation

Treadmill Mode

No

No

Yes

Indoor Cycling Cadence

No

No

Yes

Internal Memory

No

No

16 Hours

Apple Watch Integration

Yes

Yes

Yes

With the new advanced motor for KICKR BIKE, torque and voltage are measured thousands of times per second, negating any need for recalibration.

KICKR BIKE is calibrated at the factory to a power accuracy of +/- 1%

Required Tools:

Phillips Screwdriver

5mm Allen Key (Hex Key)

Wire Cutters or Scissors (to cut zip ties)

Pedal wrench or appropriately sized Allen Key for pedal removal

Specialized KICKR BIKE shipping boxes (x2) (provided by Wahoo Support )

Estimated Disassembly + Packaging Time:

15 to 30 minutes

Instructions:

Begin by zeroing the KICKR BIKE's tilt to the level position by double tapping the tilt button, shown below.

Next, disconnect the power adapter (if you haven't already) and remove the pedals, handlebar, and seat post assemblies.

Extend the setback adjustment (where the seat post was just removed) to its longest position.

Lower the stand over adjustment to its shortest level (A).

Remove the plug under the setback adjustment. While this can often be done by just pulling, a flat head screwdriver or similar may be needed to pry.

Cut any zip ties holding the wires together or to the plug. Be careful to avoid cutting the wires or letting them fall back into the unit. We advise placing a screwdriver, pen, or even a finger between the two wires as a further precaution against this.

Separate the wires at their connection from the wider end by pressing on the tab near the wires. Do not try to separate these wires at the narrower end - see the image below for details.

Push the lower wire back into the unit to ensure it does not catch when removed.

Using a Phillips screwdriver, remove the bottom-most front screw located in the recession in the plastic just above the crank, as pictured below.

Remove the KICKR BIKE's upper assembly in its entirety, now that it's free.

After removing the upper assembly, shorten and clamp all adjustment points for shipping and tuck all wires into the frame to prevent damage.

Tilt KICKR BIKE back for easy access to the 5mm Allen Key (Hex Key) screws underneath.

Remove the 5mm screws retaining the unit's right side leg (shown on the bottom left in the image below).

Once the screws for the right side leg are removed, take the larger piece of foam out of the smaller shipping box and lay it near the unit's right side. Then, detach the unit's right side leg and carefully lay the unit on the foam on its right side before removing the last remaining 8 screws, as shown below.

Once the unit is on the box and the remaining screws have been removed, detach the left leg, then the front leg from the unit to complete disassembly.

With all legs removed, turn the crank so that the left side points directly upwards toward the seat post to allow the lower portion of the KICKR BIKE to fit neatly in the box, as pictured. Place the power block in this box as well in the central hollow near the tilt mechanism. When complete, place the narrower piece of foam on top with the circular cutout over the flywheel and pack back into the smaller shipping box.

Remove the foam from the larger shipping box and place the larger foam piece on the ground.

Place the seat and seat post in the lowest portion of the triangular cutout.

With all adjustment points shortened and clamped down, place the upper assembly in the remaining section of the triangular cutout on top of the seat and seat post.

The 2 smaller leg pieces fit in the lower portion of the long cutout, with the center leg on top.

Loosen (but do not remove) the 4 bolts on the handlebar assembly so that the handlebar stem swings freely. The handlebar assembly will fit snugly into the "E" shaped cutout, as pictured.

Place the thinner piece of foam back on top when complete and pack back into the larger shipping box.

This page describes how to update firmware from an iOS device. For Android devices, see How to Update Wahoo Smart Trainer Firmware (Android). Note: the Wahoo Smart Trainer firmware can only be updated from iOS and Android devices.

Wahoo updates your KICKR's firmware (a kind of software) frequently to deliver the best indoor training experience possible. Ensuring you have the latest firmware resolves many issues, keeping you cranking and on the podium.

Requirements:

ABluetoothenabled iOS device on iOS 11 or newer

Your iOS device actively connected to the internet over WiFi

The Wahoo app for iOS

A KICKR that is not connected to any additional apps or devices (ensure previously connected devices are off/disabled and no other apps are running in the background)

Update Steps:

Ensure Bluetooth is enabled in your iOS settings and that your device is within 5 feet of the KICKR, then follow these steps to pair your KICKR:

Open the Wahoo app and check that your KICKR is plugged in and powered on. signal interference article

Select LINKED SENSORS in the bottom section of the Workout page.

Select Add New Sensorif you have yet to pair your trainer. Otherwise, simply select your already saved trainer and tap Update Firmware (which appears any time an update is available), then skip to step 7.

Choose your KICKR from the list of available sensors.

Once certain you are connected to the correct trainer, select Save Sensor, choose the workout profiles you would like your KICKR to be active for (ex. Indoor Cycling), then tap Done in the upper right corner.

Upon establishing a connection with your KICKR, the Wahoo Fitness app will determine if your KICKR's firmware is out of date. If an update is available, the app will display a prompt to Update Now.

Click Update Now and leave your iOS device near the KICKR until the update is complete.

Once the update is finished, you're prompted to toggle Bluetoothoff and back on in the iOS Settings app to refresh the connection. We also recommend you restart your trainer by unplugging it for 30 seconds after an update.

Your Wahoo smart trainer is now on the latest firmware and ready to ride!

If you encounter issues updating, please take a look at our to eliminate possible conflicts with other devices, then try again.

This page contains current and historical release notes for firmware updates to the ELEMNT BOLT bike computer.

For firmware installation, see How Do I Update the ELEMNT BOLT? For ELEMNT, see ELEMNT Firmware Updates ; for ROAM, see ELEMNT ROAM Firmware Updates For app updates, see ELEMNT App Updates (iOS) or ELEMNT App Updates (Android)

BOLT WB15-6268 - 20 November, 2019

Bug fixes and miscellaneous improvements

BOLT WB15-6264 - 12 November, 2019

Added: Relive sharing support

Fixed: Rerouting sounds and notifications while paused

Fixed: LEDs not matching correct HR zone

Fixed: Maps stuck in "Queued" state when downloading multiple maps

Fixed: Background workout recovery

BOLT WB15-6129 - 10 October, 2019

Improved Turn by Turn directions and routes with missing cues

Improved map download process

Fixed: Maps page sometimes incorrectly reporting download failure

BOLT WB15-6025 - 20 September, 2019

Improved off-route notifications

BOLT WB15-6023 - 19 September, 2019

Stability improvements

BOLT WB15-6019 - 17 September, 2019

Added: Support for TrainerRoad outdoor planned workouts

Fixed: Strava Live segments not syncing

Fixed: Issue with scaling current interval during planned workouts

BOLT WB15-5525- 3 September, 2019

Fixed: Max Speed data field displayed as AVG Speed when language is set to Chinese

BOLT WB15-5027- 26 August, 2019

Added: Support for ANT+ radar sensors

Fixed: Crash on long rides

Fixed: Routes with Turn by Turn not displayed in ELEMNT app

Fixed: Map pack downloads getting stuck in queue

Fixed: Incorrect L/R Balance shown for some power meters

BOLT WB15-4037 - 15 July, 2019

Patch release for improved stability

BOLT WB15-4036 - 9 July, 2019

FIXED: Climbing profile incorrectly displaying on map page

FIXED: Incorrect power values being displayed from SRM power meters

FIXED: Target BPM data field showing as BPM % when using Training Peaks workouts

FIXED: Power from Rotor 2Inpower freezing when not pedaling

BOLT WB15-3535- 26 June, 2019

FIXED: incorrect default settings

FIXED: maps not displayed in certain areas

FIXED: various stability improvements

BOLT WB15-3526 - 5 June, 2019

Added: Ability to customize Strava Live Segments page

FIXED: History page unavailable after workout

FIXED: Power meter and sensors data display errors

FIXED: Issues related to reversing routes

FIXED: Strava relative effort

BOLT WB15-2671 - 9 May, 2019

FIXED: Bug affecting Strava syncing when connected to WiFi

FIXED: Auto-calibration incorrectly appearing for select power meters when coasting

BOLT WB15-2666 - 1 May, 2019

FIXED: SRM CTF power issue creating negative power values

FIXED: Config backup not working after factory reset

FIXED: Debug map management no longer displays for standard users

FIXED: Various crash fixes

BOLT WB15-2659- 15 April, 2019

All new look & feel!

Account login & profile sync between Wahoo apps

New route sync with MTB Project and Singletracks!

More workout sharing partners: Map My Tracks, Xert, and Final Surge

Total odometer in the companion app

Improved support for multiple ELEMNTs

Support for cadence targets from TrainingPeaks planned workouts

BOLT WB15-2171 - December 19, 2018

FIXED: Bug causing momentary UI freezes.

BOLT WB15-2169 - December 17, 2018

ADDED: Integration with Pioneer Pedaling Monitor Systems (instructions here )

Improved update recovery for low level updates

Update high level crash recovery version from 1337 to 2159

BOLT WB09-2169 - 5 December, 2018

Update for Strava's new Live Segments API: Segments with an average grade lower than -.25% are no longer supported by Strava due to safety concerns. Downhill and similarly steep descending segments will not be synced.

ADDED: map support for larger tiles (required for new map updates)

FIXED: text capitalization on sensor discovery screen

FIXED: bug preventing display of left/right percent balance data for Pioneer Power Meters when set to Dual ANT+ mode

FIXED: bug preventing display of w/kg data for Pioneer Power Meters

FIXED: bug preventing display of Pioneer Power Meter mode change and magnet calibration functionality

FIXED: bug when transferring planned workouts

FIXED: bug preventing ANT+ FE-C connectivity with some third party trainers

BOLT WB09-2159 - 7 November, 2018

FIXED: ELEMNT/BOLTautomatically switching to Pioneer pedaling monitor mode

FIXED: Pioneer calibration exiting automatically after cancelling

ADDED: Support to set crank length for Favero Assioma pedals

FIXED: GPS drops after 3-4 hours

FIXED: Auto pause not working

FIXED: ANT+ sensors not reporting battery levels

FIXED: Riding Best Bike Split routes changing CLIMB gradient, but not KICKR resistance

FIXED: Incorrect target Watts in planned workouts

FIXED: Bug causing unexpected power off or reboot

FIXED: Duplicate uploads to sharing sites

UPDATED: Japanese translations

BOLT WB09-1985 - 14 August, 2018

FIXED: Issue with importing routes from specific third party apps

FIXED: Issue causing the 'Include Zeros in Avg Cadence' option failing to default to 'off' after factory reset

BOLT WB09-1983 - 30 July, 2018

FIXED: issue causing ELEMNT crashes related to low memory

FIXED: issue causing ELEMNT not to recover rides after battery dies

FIXED: issue with Komoot route sync

FIXED: issue withFitif Power meter not pairing

FIXED: issue causing Strava Live Segment page to not populate

FIXED: various other bug fixes

BOLT WB09-1980 - 18 July, 2018

FIXED: Shimano FC-R9100 power meter calibration failure

FIXED: Powertap P1's not registering crank length capability

FIXED: Grade data field displaying"- -" when climbing

FIXED: 3 second average power dropping to 0

FIXED: Power data field dropping to 0

Integration with SRAM TyreWiz

KICKR CLIMB support

BOLT WB09-1937 - 3 June, 2018

FIXED: Favero Assioma average power and cadence incorrect

FIXED: PowerTap hub power meter data low

FIXED: Issue where user has to resync starred segments before each ride

FIXED: Current grade data could fluctuate on a steady climb

FIXED: bug with Garmin Vector power meter calibration

FIXED: bug causing issues with GPS accuracy during long rides (6+ hours)

FIXED: bug causing sensor disconnects and failure to recover sensor connection after disconnect

Revise French translation for new lap

OTHER ANDROID COMPANION APP FIXES

FIXED: 'Take me to' feature unable to search for specific addresses

FIXED: Ability to enable automatic uploads not working

FIXED: MapBox crash when changing pages

BOLT WB09-1929 - 19 March, 2018

FIXED: Instantaneous power data field is inverted instead of 3 second avg power

FIXED: Pages reset on boot

FIXED: GPS dropping after 3-4 hours

FIXED: Time on BoltApp showing an hour behind for users in Turkey

FIXED: Center LED remaining lit during left turns

FIXED: Planned workout graph disappearing after changing pages

FIXED: 'Watts/KG - lap', 'Watts/KG - workout ' showing as N/A

BOLT WB09-1836 - 11 Jan 2018

UPDATES

Added support for uploading workouts to 2Peak

Added turn-by-turn notifications for Ride With GPS routes exported with course-points in TCX and GPX format

Added new data field for TrainingPeaks Variability Index

Bug fixes and other improvements

OTHER ELEMNT FIXES

Force 4iiii power meters to connect using ANT+

Improve layout for turn-by-turn popup notifications

BOLT WB09-1815 - 27 Nov 2017

UPDATES

Update BOLT to the latest maps via the map settings screen on the companion app

Configure auto-upload on a 'per site' basis

Choose to exclude zeros from the average power calculation

Upload to the web4trainer share site

Bug fixes and other improvements

OTHER ELEMNT FIXES

Improve accuracy of Auto lap Time triggers

Fix issue where temperature data lost after a workout end

Only write the sensors that are used to the FIT file

Fix issue where planned interval repeating intervals are lumped together

Fix issue where Strava goal appears for the wrong segment

Data Field: when workout time >10hrs, don't show seconds

Fix planned workout 10sec notifications or very short intervals

Fix wheel circumference issue for Elite Direto

Fix issues when performing 2nd spindown in same power cycle

Fix incorrect duration on some planned workouts

Planned Workout interval graph not showing unless workout is paused

Planned Workouts - Graph doesn't scale as difficulty percentage is changed

Planned Workouts - Laps created incorrectly after pause

Planned Workouts - Interval notifications should appear on KICKR page during a Planned Workout

Add support for web4trainer share site

OTHER ANDROID COMPANION FIXES

Now detects timezone/local changes while open

Now able to rename custom page

Shows 'This weeks' results

Fix workout details lap arrows not shift graph

Fix a GPX route import problem

Fix issue where 2nd email sent after phone restart

Show temperature in ride results

Show better error for MINI offline workouts not able to share to Komoot (need locations)

MINI climb results not displaying correctly

Improve messaging around need for Location Services

Fix missing notification for Android 8 Oreo

Workout results for lap data shows the same value for average power, max power and normalized power

Resetting HR zones is not resulting in the new HR zone data being sent to ELEMNT

OTHER IOS COMPANION FIXES

Updates for iPhone X

Add support for Web4Trainer share site

Add the option to exclude zeros from power average calculation

Fix Dropbox exporting issue

Fix heart rate & power zone bar graph pop ups not dismissing

Fix bug causing Live Track routes not to appear on Live Track site when the route is selected on ELEMNT/BOLT

Fix a crash that sometimes occurred on workout screen after sync finished

Improve elevation calibration for online MINI workouts

Fix a bug that caused mixed units and weight to be reset

ELEMNT BOLT WB09-1705 - 2 Oct 2017

Share Sites

ELEMNT BOLT can now share to the following sites on iOS and Android:

Komoot - https://www.komoot.com/

Cycling Analytics - https://www.cyclinganalytics.com

PowerTraxx - https://www.powertraxx.de

Additionally, Android users can now share with:

Google Fit - https://www.google.com/fit

Dropbox - https://www.dropbox.com

Other

Various bug fixes

ELEMNT BOLT WB09-1628 - 23 Aug 2017

PLANNED WORKOUTS

ELEMNT BOLT can now perform planned/structured workouts. Choose one of the built-in workouts or sync your upcoming training schedule from TrainingPeaks or Today's Plan. After selecting a workout from the PLANNED WORKOUTS section under the SETTINGS screen, ELEMNT will guide you through the workout highlighting your target efforts via the fields, LEDs, sounds, popup notifications and the target effort graph. At any time in the workout, you can pause your plan and also skip forward and back through the planned intervals.

ANT+ FE-C SUPPORT

ELEMNT BOLT can now connect to FE-C trainers via ANT+

ELEMNT BOLT WB09-1507 - 18 July 2017

ELEMNT BOLT LIVE TRACKING UPDATE. MORE DATA &PRIVACY CONTROLS

The Live Track site now shows more data including your breadcrumb trail, route, live ride data and charts.

You can continue to share your permanent link, though we have introduced a new temporary link that will expire at the end of the day. Once expired, the link will no longer be able to track you.

The link that is auto-posted to Facebook, Twitter and email is a temporary link that will expire at the end of the day.

You can manually expire all your links (both permanent and temporary) as well as opt-out of being shown as a 'nearby rider' on other people's map page.

Any previous links you have shared with your friends and family have now expired. You will need to share new links with them.

OTHER

Fixed an issue where starting certain routes on KICKR would cause a 100% resistance command sent to KICKR

Fix issue where the ELEMNT would auto-switch to the lap page if the lap page was disabled in the companion app

Fix an issue where ELEMNT would forget your gears teeth-count configuration

Improved translations

Improve Strava Segment notifications so long Segment names properly resize to maintain readability

ELEMNT BOLT WB09-1422 - 6June 2017

Strava Live Suffer Score data field (Strava Premium)

Improved the accuracy of Strava Live Segments on the ahead/behind(Strava Premium)

Cadence: Setting, from the companion app, to include or exclude zero's in the averagecalculations

Improved route syncing

Improvedthe quality of the data after a mid-workout shutdown and restart

Fixed an issue where a bad pressure sample could corrupt your elevation and grade data

Fixed an issue where a bad power sample could corrupt your power data

Fixed some issues transferring workouts to the companion app

Many other bug fixes

ELEMNT BOLT WB09-1344 - 3 April 2017

Fix incorrect elevation data after mid workout shutdown and recovery

Improve some button labels to fit better for various languages

Base the LEDs and power zone calculations on the 3-second average power, not instantaneous power

Update some compliance information

Improved translations

Reset to OUTDOOR mode on startup. Lots of reports of people accidentally riding in INDOOR mode and not having GPS

Fix issue where call/SMS/email notifications were hidden behind the workout paused notification

ELEMNT BOLT WB09-1337 - 14 March 2017

We are happy to announce the WAHOO ELEMNT BOLT !

This page contains current and historical release notes for firmware updates to the ELEMNT bike computer.

For firmware installation, see How Do I Update the ELEMNT? For BOLT, see ELEMNT BOLT Firmware Updates ; for ROAM, see ELEMNT ROAM Firmware Updates For app updates, see ELEMNT Companion App Updates (iOS) or ELEMNT Companion App Updates (Android)

ELEMNT WF48-6268 - 19 November, 2019

Bug fixes and miscellaneous improvements

ELEMNT WF48-6264 - 12 November, 2019

Added: Relive sharing support

Fixed: Rerouting sounds and notifications while paused

Fixed: LEDs not matching correct HR zone

Fixed: Maps stuck in "Queued" state when downloading multiple maps

Fixed: Background workout recovery

ELEMNT WF48-6129 - 9 October, 2019

Improved Turn by Turn directions and routes with missing cues

Improved map download process

Fixed: Maps page sometimes incorrectly reporting download failure

ELEMNT WF48-6025 - 20 September, 2019

Improved off-route notifications

ELEMNT WF48-6023 - 19 September, 2019

Stability improvements

ELEMNT WF48-6019 - 17 September, 2019

Added: Support for TrainerRoad outdoor planned workouts

Fixed: Strava Live segments not syncing

Fixed: Issue with scaling current interval during planned workouts

ELEMNT WF48-5525- 3 September, 2019

Fixed: Max Speed data field displayed as AVG Speed when language is set to Chinese

ELEMNTWF48-5027- 26 August, 2019

Added: Support for ANT+ radar sensors

Fixed: Crash on long rides

Fixed: Routes with Turn by Turn not displayed in ELEMNT app

Fixed: Map pack downloads getting stuck in queue

Fixed: Incorrect L/R Balance shown for some power meters

ELEMNTWF48-4540 - 14 August, 2019

Fixed: Blank map tiles when no data fields are selected

Fixed: Incorrect Turn by Turn directions on Strava routes

Fixed: Nearby riders flickering on map page

Fixed: Auto-shutdown not working correctly

Fixed: Routing issues when the finish is near the start or when "Route to start" overlaps the route

ELEMNTWF48-4037 - 15 July, 2019

Patch release for improved stability

ELEMNTWF48-4036 - 9 July, 2019

FIXED: Climbing profile incorrectly displaying on map page

FIXED: Incorrect power values being displayed from SRM power meters

FIXED: Target BPM data field showing as BPM % when using Training Peaks workouts

FIXED: Power from Rotor 2Inpower freezing when not pedaling

ELEMNTWF48-3535- 26 June, 2019

FIXED: incorrect default settings

FIXED: maps not displayed in certain areas

FIXED: various stability improvements

ELEMNTWF48-3526 - 5 June, 2019

Added: Ability to customize Strava Live Segments page

FIXED: History page unavailable after workout

FIXED: Power meter and sensors data display errors

FIXED: Issues related to reversing routes

FIXED: Strava relative effort

ELEMNTWF48-2671 - 9 May, 2019

FIXED: Bug affecting Strava syncing when connected to WiFi

FIXED: Auto-calibration incorrectly appearing for select power meters when coasting

ELEMNT WF48-2666 - 1 May, 2019

FIXED: SRM CTF power issue creating negative power values

FIXED: Config backup not working after factory reset

FIXED: Debug map management no longer displays for standard users

FIXED: Various crash fixes

ELEMNT WF48-2659- 15 April, 2019

All new look & feel!

Account login & profile sync between Wahoo apps

New route sync with MTB Project and Singletracks!

More workout sharing partners: Map My Tracks, Xert, and Final Surge

Total odometer in the companion app

Improved support for multiple ELEMNTs

Support for cadence targets from TrainingPeaks planned workouts

ELEMNT WF48-2171 - 19 December, 2018

FIXED: Bug causing momentary UI freezes.

ELEMNT WF48-2169 - 5 December, 2018

Update for Strava's new Live Segments API: Segments with an average grade lower than -.25% are no longer supported by Strava due to safety concerns. Downhill and similarly steep descending segments will not be synced.

ADDED: map support for larger tiles (required for new map updates)

FIXED: text capitalization on sensor discovery screen

FIXED: bug preventing display of left/right percent balance data for Pioneer Power Meters when set to Dual ANT+ mode

FIXED: bug preventing display of w/kg data for Pioneer Power Meters

FIXED: bug preventing display of Pioneer Power Meter mode change and magnet calibration functionality

FIXED: bug when transferring planned workouts

FIXED: bug preventing ANT+ FE-C connectivity with some third party trainers

ELEMNT WF48-2159 - 7 November, 2018

FIXED: ELEMNT/BOLTautomatically switching to Pioneer pedaling monitor mode

FIXED: Pioneer calibration exiting automatically after cancelling

ELEMNT WF48-2147 - 1 October, 2018

This release centers around integration with the Pioneer Pedaling Monitor System.

ADDED: Integration with the Pioneer Pedaling Monitor System (instructions here )

ADDED: Support to set crank length for Favero Assioma pedals

FIXED: GPS drops after 3-4 hours

FIXED: Auto pause not working

FIXED: ANT+ sensors not reporting battery levels

FIXED: Riding Best Bike Split routes changing CLIMB gradient, but not KICKR resistance

FIXED: Incorrect target Watts in planned workouts

FIXED: Bug causing unexpected power off or reboot

FIXED: Duplicate uploads to sharing sites

UPDATED: Japanese translations

ELEMNT WF42-1985 - 14 August, 2018

FIXED: Issue with importing routes from specific third party apps

FIXED: Issue causing the 'Include Zeros in Avg Cadence' option failing to default to 'off' after factory reset

ELEMNT WF42-1983 - 30 July, 2018

FIXED: issue causing ELEMNT crashes related to low memory

FIXED: issue causing ELEMNT not to recover rides after battery dies

FIXED: issue with Komoot route sync

FIXED: issue withFitif Power meter not pairing

FIXED: issue causing Strava Live Segment page to not populate

FIXED: various other bug fixes

ELEMNT WF42-1980 - 18 July, 2018

FIXED: Shimano FC-R9100 power meter calibration failure

FIXED: Powertap P1's not registering crank length capability

FIXED: Grade data field displaying"- -" when climbing

FIXED: 3 second average power dropping to 0

FIXED: Power data field dropping to 0

Integration with SRAM TyreWiz

KICKR CLIMB support

ELEMNT WF42-1937 - 3 June, 2018

FIXED: Favero Assioma average power and cadence incorrect

FIXED: PowerTap hub power meter data low

FIXED: Issue where user has to resync starred segments before each ride

FIXED: Current grade data could fluctuate on a steady climb

FIXED: bug with Garmin Vector power meter calibration

FIXED: bug causing issues with GPS accuracy during long rides (6+ hours)

FIXED: bug causing sensor disconnects and failure to recover sensor connection after disconnect

Revise French translation for new lap

OTHER ANDROID COMPANION APP FIXES

FIXED: 'Take me to' feature unable to search for specific addresses

FIXED: Ability to enable automatic uploads not working

FIXED: MapBox crash when changing pages

ELEMNT WF42-1929 - 19 March, 2018

FIXED: Instantaneous power data field is inverted instead of 3 second avg power

FIXED: Pages reset on boot

FIXED: GPS dropping after 3-4 hours

FIXED: Time on BoltApp showing an hour behind for users in Turkey

FIXED: Center LED remaining lit during left turns

FIXED: Planned workout graph disappearing after changing pages

FIXED: 'Watts/KG - lap', 'Watts/KG - workout ' showing as N/A

ELEMNT WF42-1836 - 11 Jan 2018

UPDATES

Added support for uploading workouts to 2Peak

Added turn-by-turn notifications for Ride With GPS routes exported with course-points in TCX and GPX format

Added new data field for TrainingPeaks Variability Index

Bug fixes and other improvements

OTHER ELEMNT FIXES

Force 4iiii power meters to connect using ANT+

Improve layout for turn-by-turn popup notifications

ELEMNT WF42-1815 - 27 Nov 2017

UPDATES

Update ELEMNT to the latest maps via the map settings screen on the companion app

Configure auto-upload on a 'per site' basis

Choose to exclude zeros from the average power calculation

Upload to the web4trainer share site

Bug fixes and other improvements

OTHER ELEMNT FIXES

Improve accuracy of Auto lap Time triggers

Fix issue where temperature data lost after a workout end

Only write the sensors that are used to the FIT file

Fix issue where planned interval repeating intervals are lumped together

Fix issue where Strava goal appears for the wrong segment

Data Field: when workout time >10hrs, don't show seconds

Fix planned workout 10sec notifications or very short intervals

Fix wheel circumference issue for Elite Direto

Fix issues when performing 2nd spindown in same power cycle

Fix incorrect duration on some planned workouts

Planned Workout interval graph not showing unless workout is paused

Planned Workouts - Graph doesn't scale as difficulty percentage is changed

Planned Workouts - Laps created incorrectly after pause

Planned Workouts - Interval notifications should appear on KICKR page during a Planned Workout

Add support for web4trainer share site

OTHER ANDROID COMPANION APP FIXES

Now detects timezone/local changes while open

Now able to rename custom page

Shows 'This weeks' results

Fix workout details lap arrows not shift graph

Fix a GPX route import problem

Fix issue where 2nd email sent after phone restart

Show temperature in ride results

Show better error for MINI offline workouts not able to share to Komoot (need locations)

MINI climb results not displaying correctly

Improve messaging around need for Location Services

Fix missing notification for Android 8 Oreo

Workout results for lap data shows the same value for average power, max power and normalized power

Resetting HR zones is not resulting in the new HR zone data being sent to ELEMNT

OTHER IOS COMPANION APP FIXES

Updates for iPhone X

Add support for Web4Trainer share site

Add the option to exclude zeros from power average calculation

Fix Dropbox exporting issue

Fix heart rate & power zone bar graph pop ups not dismissing

Fix bug causing Live Track routes not to appear on Live Track site when the route is selected on ELEMNT/BOLT

Fix a crash that sometimes occurred on workout screen after sync finished

Improve elevation calibration for online MINI workouts

Fix a bug that caused mixed units and weight to be reset

ELEMNT WF42-1705 - 2 Oct 2017

Share Sites

ELEMNT BOLT can now share to the following sites on iOS and Android:

Komoot - https://www.komoot.com/

Cycling Analytics - https://www.cyclinganalytics.com

PowerTraxx - https://www.powertraxx.de

Additionally, Android users can now share with:

Google Fit - https://www.google.com/fit

Dropbox - https://www.dropbox.com

Other

Various bug fixes

ELEMNT WF42-1628 - 23 Aug 2017

PLANNED WORKOUTS

ELEMNT can now perform planned/structured workouts. Choose one of the built-in workouts or sync your upcoming training schedule from TrainingPeaks or Today's Plan. After selecting a workout from the PLANNED WORKOUTS section under the SETTINGS screen, ELEMNT will guide you through the workout highlighting your target efforts via the fields, LEDs, sounds, popup notifications and the target effort graph. At any time in the workout, you can pause your plan and also skip forward and back through the planned intervals.

ANT+ FE-C SUPPORT

ELEMNT can now connect to FE-C trainers via ANT+

ELEMNT WF42-1507 - 18 June 2017

ELEMNT LIVE TRACKING UPDATE. MORE DATA &PRIVACY CONTROLS

The Live Track site now shows more data including your breadcrumb trail, route, live ride data and charts.

You can continue to share your permanent link, though we have introduced a new temporary link that will expire at the end of the day. Once expired, the link will no longer be able to track you.

The link that is auto-posted to Facebook, Twitter and email is a temporary link that will expire at the end of the day.

You can manually expire all your links (both permanent and temporary) as well as opt-out of being shown as a 'nearby rider' on other people's map page.

Any previous links you have shared with your friends and family have now expired. You will need to share new links with them.

OTHER

Fixed an issue where starting certain routes on KICKR would cause a 100% resistance command sent to KICKR

Fix issue where the ELEMNT would auto-switch to the lap page if the lap page was disabled in the companion app

Fix an issue where ELEMNT would forget your gears teeth-count configuration

Improved translations

Improve Strava Segment notifications so long Segment names properly resize to maintain readability

ELEMNT WF42-1422 - 6June 2017

Strava Live Suffer Score data field (Strava Premium)

Improved the accuracy of Strava Live Segments on the ahead/behind(Strava Premium)

Cadence: Setting, from the companion app, to include or exclude zero's in the averagecalculations

Improved route syncing

Improvedthe quality of the data after a mid-workout shutdown and restart

Fixed an issue where a bad pressure sample could corrupt your elevation and grade data

Fixed an issue where a bad power sample could corrupt your power data

Fixed some issues transferring workouts to the companion app

Many other bug fixes

ELEMNT WF42-1344 - 3 April 2017

Fix incorrect elevation data after mid workout shutdown and recovery

Improve some button labels to fit better for various languages

Base the LEDs and power zone calculations on the 3-second average power, not instantaneous power

Update some compliance informationImprove some translations

Reset to OUTDOOR mode on startup. Lots of reports of people accidentally riding in INDOOR mode and not having GPS

Fix issue where call/SMS/email notifications were hidden behind the workout paused notification

ELEMNT WF42-1337 - 17 February 2017

Improved fonts

The SMS and email notifications can now be read in a full-screen window

Added the ability to cycle from the bottom back to the top of menus

You can now have 11 fields on the main pages

ELEMNT WF42-1245 - 11 January 2017

Fixes an approximately 20-second hang sometimes seen on ELEMNT startup

Improved elevation algorithm to detect and correct long period elevation drift

ELEMNT WF42-1219 - 14 December 2016

Fixed an issue causing some sensors to take a long time to connect after bootup

Map will now honor the user's auto-rotate setting for all zoom levels

Improved translations

ELEMNT WF42-1217 - 17 November 2016

Summary

Route Me Anywhere: On the Companion App, enter a destination, address, or point of interest to generate a route optimized for cycling, complete with turn-by-turn navigation.

Back to Start: Either on the ELEMNT or the Companion App, selecting this option will create a route back to your ride's starting point, on the same way you came.

Route Sync via Bluetooth: All the magic of Wi-Fi route syncing can now be done over Bluetooth! Send any route to your ELEMNT with only your smartphone.

Routes

Ride any route in reverse

Ride route back to start along breadcrumb path

Support for importing GPX, TCX and FIT route files via USB

Support for selecting route from companion app

Support for sending any route from companion app to ELEMNT using Bluetooth (no Wifi)

Support for "Route Me Anywhere" routes from companion app

Fixed OFF Route notification only staying on for a short time

Fixed Komoot roundabout exit number

Improvements to RideWithGPS turn by turn parsing

Fixed distance to go not updating on route detail screen

Share

Disable support Garmin Connect (they are no longer allowing us to upload files)

Fixed issues with some RideWithGPS passwords

Workouts

Fixed issue with distance not incrementing after workout recovery

Fixed Normalized Power, IF and TSS calculations

Improved ANT+ Connection

Other

Greatly improved UI responsiveness

Improved battery life

Tweak LED brightness

Added LED settings to ELEMNT menu

Several other crash and stability improvements

Localisation fixes

ELEMNT WF42-1012 - 31 August 2016

This marks our 15th public release since February and its primary focus has been some great additional 3rd party support along with a heapof data fields requested by our users. Enjoy!

BestBikeSplit ( http://bestbikesplit.com )

Sync Course and Race plans from BestBikeSplit

BestBikeSplit advanced KICKR simulation- Simulated weather conditions- Road Rolling Resistance- Wind Effect- Air density- Rider drag- Dynamic weight during long courses

Komoot ( http://komoot.de )

Sync Tours from Komoot with turn by turn directions. Komoot provides a unique, high quality routing engine with some great additional information like road surface.

Updates and Fixes

Support for 6, 7 & 8 Power zones including LED indication of current zone

Re-order history so power is higher up the list

Fixed issue with some of the history detail being cut off

Disable live segments for Flagged Segments

Updated some translations based on user feedback

Added Thai language support

Fixed continuous beeps on some route turns. Beep once when the banner is shown and once again just before the turn.

Fixed layout of TurnByTurn banner on map page with no data fields

Fixed Ride Recovery from not recovering after reboot

45 New Data Fields!!

Distance (last lap)

Total Ascent (last lap)

Total Descent (last lap)

Grade (workout average, lap average, last lap average)

Power (last lap average)

Power/FTP % (instant, workout, lap, last-lap, 3sec, 5sec, 20sec & 30sec)

Watts/kg (workout average, lap average, last lap average)

L/R Balance (last lap)

L/R Balance fields now formatted with 2 values. eg 55/45

Pedal Smoothness (current, workout, lap, last lap) + include in FIT file

Torque Effectiveness (current, workout, lap, last lap) + include in FIT file

Normalised Power (Lap & Last Lap)

Intensity Factor data field now has 2 decimal places

Torque (workout average, lap average, last lap average)

Heart rate (last lap average)

Speed (last lap average)

Cadence (last lap average)

Power (Time in Zone graphic)

Added time in Power zone to FIT file

Heart rate (Time in Zone graphic)

Target Power (BestBikeSplit Races)

Target Speed (BestBikeSplit Races)

Routes distance to go

Routes distance to next cue

-------------------------------------------------------------------------------------------------

ELEMNT WF42-873 - 16th August2016

Fixed issue with RideWithGPS Pinned Routes not syncing when user has Pinned rides

Fixed several rare crashes

Improved localisations

-------------------------------------------------------------------------------------------------

ELEMNT WF42-870 - 3rdAugust2016

STRAVA Live Segments!

ELEMNT is now fully integratedwith Strava Live Segments to give you accurate progress status and the Final Push to beat your goals

- Starred segments on your Strava account wirelessly upload to ELEMNT- Notifications prior to a segment start so you don't miss a second- See your status on the segment vs. the Leader, your PR, and your friends as the segment progresses- ELEMNT allows you to ride Routes & Strava Live Segments simultaneously- Get a Final Push when you are close to hitting a goal so you never miss an opportunity to be your very best.

Other Great additions

- Added LED/Buzzer to START workout reminding- Added Turn by Turn buzzer and increased LED brightness- Added support for PINNED routes from RideWithGPS- Added support for TCX Routes- Added Sporttracks.mobi uploads- Added background recovery to repair FIT files- Added recovery % progress and cancel button (sends to background)- Improved ANT+ Connection management- Fixed: Improved auto-upload logic for better performance- Fixed: Wifi not turning off after uploads finished- Fixed: Improved support for roundabouts in turn by turn.- Fixed: Added confirmation before adding data fields when pairing new sensor- Fixed: Duplicate power fields when using with KICKR- Fixed issue with gaps in temperature data.

iOS 1.4.0

- All new History detail, graphs and data- Added support for showing Strava Segment results- Added support for importing TCX Routes- Fixed battery drain issues

Android 1.4.0

- All new History detail, graphs and data- Added support for showing Strava Segment results- Added support for importing TCX Routes

https://www.sram.com/sram/road/family/sram-red-etap

-------------------------------------------------------------------------------------------------

iOS1.3.3 - 12th July 2016

Fixed: Crash when viewing some history detail.

Fixed: issue uploading to third party sites.

iOS1.3.1 - 27th June 2016

A bug fix release to fix some pesky crash issues.

Fixed: Mixed units was not changing height.

Fixed: Crash bug checking Wahoo Sensors for firmware upgrade.

Fixed: Crash when deleting workout on ELEMNT.

ELEMNT WF42-630 - 23rd June 2016

Fixed crash loop bug in workout recovery

Fixed bug that caused Recovering Workout to Display on start up

ELEMNT WF42-628 - 15th June2016

Routes/Maps

Added support for Turn by Turn navigation (RideWithGPS only)

Improvements to Route following especially out and back routes

Added support for up to 6 data fields on map workout page

After selecting a route it now goes straight back to the map view

Added a new "Selected" route view with full cue sheet if available

Added ability to sort routes by date, proximityand starred

Fixed issue of deleted routes not clearing from ELEMNT

Workout

Added notification if moving but have not started a workout

Added support powering off your ELEMNT mid-workout

Added option to delete workout if under time/distance thresholds

Scroll through workout history on ELEMNT

Configuration

Added support for mixed units. e.g distance miles, temp deg C, elevation in metres

Added support for connecting to hidden Wifi networks (using SSID/password)

Added support for manually switching between known Wifi networks with companion app

Added support for showing SSIDs longer than 16 characters

Added low storage warning

Sensor Support

Added support for configuring gear ratios (from companion app)

Improved support for PowerTap P1 and Polar Look power meters

Added support for PowerCal

Fixed issue of Normalized Power spikes

Added clock drift compensation for sensor device clocks

Fixed issue with sensor info in FIT file all having manufacturer set to Wahoo

Added support for a single front gear (Shifting profile)

UI/UX Tweaks

Optimized power calibration by skipping "prepare" page

Fixed menu selection not visible when backing out of menus

Fixed issue with P1 battery status showing incorrect labels

Remove battery status for KICKR devices

Added firmware information to sensor info page

Fixed issue with battery information not updating if status page is open

I am sure I must have missedsomething

Other bug fixes and enhancements ;-)

iOS 1.3.0 (74) - 15th June 2016

Make sure you update your ELEMNT, most of the goodness comes from the update above!

New - Add up to 6 fields on the map page.

New - You can now have mixed units. e.g distance miles, temp deg C, elevation in metres.

New - You can now update your firmware for Wahoo sensors within companion app.

New - Configure Electronic gears.

New - You can now delete routes.

New - Upload to Dropbox (from companion only).

New - Can now connect to a hidden WiFi network.

New - Delete workouts - workouts deleted on companion or ELEMNT are deleted everywhere.

Fixed - Crash on customize pages.

Fixed - Can now set crank length & wheel size for sensors.

Fixed - Numerous other bug fixes.

-------------------------------------------------------------------------------------------------

ELEMNT WF42-435 - 7th June2016

This is afirmware update for ELEMNT and fixes two very important issues. There are no changes to the ELEMNT app.

Fixed short (2-10sec) sensor and phone connection dropouts.

Fixed LED flicker

Note: The ELEMNT may take a fewminutes to boot after installing this update, a progress bar will be shown on the screen.

iOS 1.2.6 (68)- 24thMay 2016

Fixedauthentication to Today's Plan

Fixed a bug preventing some people from customizing their pages

ELEMNT WF38-435 - 16th May 2016

Fixed issue of WiFi network being forgotten

Fixed issue of WiFi not connecting

Adding new sensor is no longer blocked by WiFi activity

Improved translations

Improved stability and fixed a couple rare crashes

iOS 1.2.5 (67) - 16th May 2016

RideWithGPS now using the FIT file

Fixed issue with Auto-Lap time not matching ELEMNT

Added support for new authentication/upload for TrainingPeaks

Improved UI loading when opening the app from the background

Improved UI for ELEMNT disconnects and BT disabled.

Improvements to translations

Several other small UI/UX improvements and spelling errors.

-------------------------------------------------------------------------------------------------

ELEMNT WF38-420 / iOS 1.2.4 (60) / Android 1.2.0.12 - 4th May 2016

Focusing on improving the ELEMNTs mapping, workout recording, syncing and sharing, the ELEMNT WF38-420 (and companion app) release includes the following core updates:

FIT on the Fly (New & improved method for transferring ride data to the app/cloud) Allows for exceptionally faster and more reliable data syncing.

Map Management - Add/remove world maps to the ELEMNTs built-in memory.

Map Rotation - Allowing riders to orient the map according to the direction they are currently traveling as well as the current North-facing setting, users can now toggle between the two via the ELEMNT companion app.

Map Style Improvements - The map page will now keep trails/local roads displayed on the screen for an additional two zoom levels.

Improved Tracking - More data points will improve the accuracy of 'bread-crumb' navigation.

To update to the current firmware, youll need to connect your ELEMNT to your home network and then navigate to the setup menu where youll press the 'System Info' option, followed by the 'Check' option that will appear when the current firmware version is highlighted.

Full change log below:

ELEMNT WF38-420

Big improvements to sync speed and reliability.

Fixes missing/mismatched values between ELEMNT, the phone and 3rd Party sites

Always have access to the original FIT data on any device, any time.

Added all new history detail post workout with all your stats (automatically shown post workout)

Added option to always rotate the Map in your direction of travel

Maps: Keep roads, cycle paths, trails and footways around at higher zoom levels

Maps: Fixed rendering issues of bridges

Maps: Fixed rendering issues of some types of trails

Improved speed of UI updates of power data

Fixed issue with Routes not syncing from phone apps (via Wahoo Cloud)

Fixed several missing and incorrect localisations (let us know if you find any)

iOS notifications are not dismissed on ELEMNT when read on iPhone

Fixed issue with time format not matching users (phone) settings

Improved styling of menus

Improved formatting of data fields for consistency

Changed FIT file name format to follow industry standard

Fixed issue with Route taking a very long time to load

Improved support for TrainingPeaks login

Fixed a few crashes when navigating menus

iOS Companion App 1.2.4 (60)

Added auto-upload support from the phone

Much improved sync speed and reliability

Added ability to manage maps on ELEMNT (Add/Remove/Update)

Added FIT file export to all share sites and email

Added elevation chart to history detail view

Added charging reminding for ELEMNT

Added notifications for new ELEMNT software updates

Improved share site UI

Fixes for missing/mismatched values between ELEMNT/Phone

Fixed support for re-ordering/deleting custom pages

Fixed issues with 3rd party site credentials not being synced with ELEMNT

Fixed support for syncing Routes when using Facebook sign in

Fixed updating Live Tracking when finishing workout

Added iOS low storage warning

Fixed several pesky user reported crashes

Android Companion App1.2.0.12

Much improved sync speed and reliability

Fixes for missing/mismatched values between ELEMNT/Phone

Added auto-upload support from the phone

Added support for setting power meter crank length

Added ability to manage maps on ELEMNT (Add/Remove/Update)

Fixed a crash when uploading to Training Peaks

Improved localizations

General stability and UI improvements

-------------------------------------------------------------------------------------------------

ELEMNT WF38-228 - 31st March 2016

Fixed issue with languages being reset to English when connecting to iOS.

Fixed 0 Watts not being recorded when coasting (crank/pedal power meters).

Fixed Xsec/Xmin Moving power averages, now based from absolute time not active time.

Fixed some issues with Normalised and TSS values being very high

ELEMNT WF38-221 - 23rd March 2016

Added support for 9 new languages. French, Dutch, German, Korean, Japanese, Spanish, Chinese (Simplified), Italian, Portuguese (Brazil)

Added support for Muscle Oxygen sensors (eg. Moxy and BSXInsight)

https://www.bsxinsight.com

http://www.moxymonitor.com

Added support for Di2 gear and battery display. (D-Fly required)

http://bike.shimano.com/content/sac-bike/en/home/articles/d-fly.html

Added support for SRAM eTap gear and battery display

SRAM eTap and Di2 Gear information

SM02 Support

ELEMNT WF38-219 - 18th March 2016

Added Smoothed Torque field

Added 3s/5s/10s/20s/30s/1min/5min/20min/30min/1hr Avg Power fields

Added LED & Audio alerts to Lap events

Added better audio alerts for pause/resume.

Added map scale bar

Added new battery icon when ELEMNT is on charge

Added support for latest KICKR firmware (1.4.40.0)

Added KICKR no-control mode for when using with 3rd party software at the same time

Added sensor information page to display ID, Network and other info

Hide Map and Climb page when connected to a KICKR and not in Route mode.

Improved consistency in AVG/MAX/LAP titles

Improved support for latest Wahoo Cadence (>=2.0.16)

Improved auto-pause logic to remove false pauses.

Fixed map detail in London, Paris & Amsterdam.

Fixed climb graph scaling

Fixed with with temperature readings being 5C/9F too high.

Fixed 0 average speed and average power values on display.

Fixed crash when quickly cycling through workout pages

Fixed pairing ANT+ HR when >25 sensors are in range.

Fixed KJ value being 4x too high.

Fixed reporting of ELEMNT version to companion apps.

ELEMNT WF38-164 - 25thFeb2016

Fixed false auto-pauses on some sensor dropouts

Fix for Polar BT sensors

ELEMNT WF34-162 - 12thFeb2016

Improved speed of workout transfer to companion app.

Improvedhandling when you lose/forget your speed sensor magnet.

Removed LED function override when pairing a power meter.

Removed TSS/KJ fields overridewhen pairing power meter.

Fixed Bluetooth connection stability to phone and sensors

Fixed Bluetooth error causing required reboot

Fixed network communications on some wifi networks.

Fixed reconnection of ANT+ Speed & Cadence sensor.

Fixed crash when stopping sensor (ANT+) discovery.

Fixed issue with temperature sensor starting.

Fixed crash when closing the route menu.

Fixed FIT file not visibleup on USB after ride.

Fixed crash when importing route from ride history (via companion app).

Fixed crash when finishing very long workout (8+ hours).

This page contains current and historical release notes for firmware updates to the ELEMNT bike computer.

For firmware installation, see How Do I Update the ELEMNT? For BOLT, see ELEMNT BOLT Firmware Updates ; for ELEMNT, see ELEMNT Firmware Updates For app updates, see ELEMNT Companion App Updates (iOS) or ELEMNT Companion App Updates (Android)

ELEMNT ROAM WR14-6268 - 20 November, 2019

Minor bug fixes and miscellaneous improvements

ELEMNT ROAM WR14-6264 - 12 November, 2019

Added: Relive sharing support

Fixed: Rerouting sounds and notifications while paused

Fixed: LEDs not matching correct HR zone

Fixed: Maps stuck in "Queued" state when downloading multiple maps

Fixed: Background workout recovery

ELEMNT ROAM WR14-6129 - 8 October, 2019

Improved Turn by Turn directions and routes with missing cues

Improved map download process

Fixed: Maps page sometimes incorrectly reporting download failure

ELEMNT ROAM WR14-6025 - 20 September, 2019

Improved off-route notifications

ELEMNT ROAM WR14-6023 - 19 September, 2019

Stability improvements

ELEMNT ROAM WR14-6019 - 17 September, 2019

Added: Support for TrainerRoad outdoor planned workouts

Fixed: Strava Live segments not syncing

Fixed: Issue with scaling current interval during planned workouts

ELEMNT ROAM WR14-5525- 3 September, 2019

Added: Re-routing improvements when a rider re-joins a route after going off course

Fixed: Max Speed data field displayed as AVG Speed when language is set to Chinese

ELEMNT ROAM WR14-5027- 26 August, 2019

Added: Support for ANT+ radar sensors

Fixed: Crash on long rides

Fixed: Routes with Turn by Turn not displayed in ELEMNT app

Fixed: Map pack downloads getting stuck in queue

Fixed: Incorrect L/R Balance shown for some power meters

ELEMNT ROAM WR14-4541 - 20 August, 2019

Fixed: Issue with available memory for maps

ELEMNT ROAM WR14-4540 - 14 August, 2019

Fixed: Blank map tiles when no data fields are selected

Fixed: Incorrect Turn by Turn directions on Strava routes

Fixed: ROAM incorrectly reporting insufficient space on map download

Fixed: Nearby riders flickering on map page

Fixed: Auto-shutdown not working correctly

Fixed: "Route to start" failing to start route on arrival

Fixed: Routing issues when the finish is near the start or when "Route to start" overlaps the route

Improved: Countries with large map files are now split into smaller, more manageable regions

Improved: Routes starting over 200m away now ask to "Route to Start" on load (previously 1km)

Improved: Better ROAM directions in roundabouts

ELEMNT ROAM WR10-4039 - 26 July, 2019

FIXED: Storage space discrepancy preventing map downloads and updates

ELEMNT ROAM WR10-4037 - 15 July, 2019

Patch release for improved stability

ELEMNT ROAM WR10-4036 - 9 July, 2019

FIXED: Climbing profile incorrectly displaying on map page

FIXED: Incorrect power values being displayed from SRM power meters

FIXED: Target BPM data field showing as BPM % when using Training Peaks workouts

FIXED: Power from Rotor 2Inpower freezing when not pedaling

ELEMNT ROAM WR10-3535- 26 June, 2019

FIXED: turn by turn directions not always displayed

FIXED: re-routing setting always on

ELEMNT ROAM WR10-3526 - 5 June, 2019

Added: Ability to customize Strava Live Segments page

Added: Turn By Turn (TBT) support for Strava and other routing sources

FIXED: History page not available after a workout

FIXED: Power meter dropouts and sensors showing no data

FIXED: Reversing a route not working

FIXED: Strava relative effort

FIXED: Bug related to TBT directions disappearing

FIXED: Routing and re-routing calculation times improved (speedier routing)

ELEMNT ROAM WR10-3082 - 21 May, 2019

FIXED: blank map management screen

ELEMNT ROAM WR10-3079 - 14 May, 2019

Timer added to ambient light sensor

FIXED: SRM calibration issue

FIXED: speed spikes when initialized in poor GPS areas

ELEMNT ROAM WR10-ROAM 3070 - 25 April, 2019

Initial release

This article describes Android compatibility with the Wahoo Fitness app. For cycling computers, see the Android compatibility articles for the ELEMNT or ELEMNT BOLT.

Wahoo App for Android Compatibility:

The Wahoo App for Android from the Google Play Store supports the following Wahoo devices:

TICKR, TICKR X, and TICKR FIT

BlueHR & BlueSC

RPM SPD & RPM Cadence

All KICKR and SNAP versions (including KICKR BIKE)

Android System Requirements:

Android version 6 or newer with third party app access to Bluetooth

Bluetooth 4.0 (or newer) compliance

Compatible Devices:

Since Android hardware varies widely, compatibility is not assured for all devices. Please download and install the Wahoo App for Android from the Google Play Store before purchasing a Wahoo Fitness product to ensure compatibility.

The Wahoo App for iOS is designed to work with any Apple device on iOS 11 or newer. To check the iOS version of your Apple device, please see Find the software version on your iPhone, iPad, or iPod.

As the app is updated frequently, please download the Wahoo Fitness app from the Apple App Store before purchase to ensure compatibility.

The following Wahoo devices are supported in the Wahoo Fitness App:

All KICKR, CORE, and SNAP versions (including KICKR BIKE)

TICKR, TICKR RUN, TICKR X, and TICKR FIT

RPM Speed & Cadence

BlueHR & BlueSC

Wahoo Smart Trainerswill work out of the box with several software solutions. If you know of one that is not currently listed, please let us know!

Wahoo Fitness AppWahoos App controls the KICKR in four different ways

Level mode:Weve built 10 levels, each with a progressive resistance curve, just like riding outside. For example, the faster you pedal, the harder it gets simulating rolling and air resistance.

Erg mode:With the KICKR, you can set a target wattage and the KICKR will remain at that wattage as you ride independent of speed and cadence. This is the ultimate way to train with Power.

Sim mode:With sim mode, you can enter your weight, bike type, riding position, headwind, and grade and the KICKR will accurately model the power curve just as if you were riding outdoors.

Resistance mode:For those of you who need to be in control, this allows you to adjust resistance of the brake manually from 0 to 100%

ZwiftZwift is the first company to use massive multiplayer gaming technology to bring the outdoor cycling experience indoors. Athletes from around the globe can ride with each other in rich 3D generated worlds simply by connecting their existing devices (e.g. trainers, power meters, heart rate monitors, etc) wirelessly via open Industry standard ANT+ or BLE. From structured workouts and training plans to friendly competition and casual group rides, Zwift is building a community of like-minded athletes united in the pursuit of a better indoor cycling experience.

Trainer RoadTrainer Road.com is an online community focused on providing cyclists incredible structured workouts and training programs. Check out www.trainerroad.com for more information

KinomapKinomap is an online sharing site of geolocated videos. Choose a video of your favorite Tour stage or race course and Kinomap will control the KICKR as you watch the video, matching the resistance to the elevation of your virtual ride. Check out trainer.kinomap.com for more information.

Any ANT+ head unitThe KICKR broadcasts speed and power (wattage) via ANT+. Any ANT+ enabled bike computer, such as a Garmin Edge, will be able to read the data from your KICKR. Any ANT+ FE-C head unit can also control the KICKR and adjust resistance.

While the Apple Watch cannot be used to display or record heart rate data in the Wahoo Fitness app, TICKR Heart Rate Monitors (including TICKR, TICKR X, and TICKR FIT) can be paired to an Apple Watch to provide more accurate heart rate data in the Apple Watch Workout app following the instructions below:

To pair the Apple Watch with your TICKR:

Wake your TICKR by wearing it or touching the back terminals (for TICKR FIT, wake by pressing the power button) so that the lights begin to blink.

On your Apple Watch, open the Settings app to the Bluetooth section.

Select your TICKR when it appears under the Health Device* list

To record a workout, open the Apple Watch Workout app, select your workout type, then tap Open Goal to begin the workout.

*If you don't see your TICKR under Health Devices, close the Settings screen on the Apple Watch and reopen it to update sensors. Please note that although the Apple Watch identifiesTICKR Heart Rate Monitors as health devices, they are designed and tested exclusively as athletic products and are not intended for health monitoring or related applications.

For Android, please see ELEMNT App Updates (Android)

ELEMNT App for iOS 1.25.0 - November 12, 2019*

Added: Relive sharing support

Fixed: Weight/height changes overwritten by Apple Health

Fixed: Korean translations

*This release will roll out slowly to select users until full distribution on November 19, 2019.

ELEMNT App for iOS 1.24.0 - October 2, 2019*

Fixed: MINI auto pause not working

Fixed: MINI workouts showing 100% of time in peak HR zone

Added: iOS 13 dark mode updates

Battery drain improvements

Additional Stability improvements

*This release will roll out slowly to select users until full distribution on October 9, 2019.

ELEMNT App for iOS 1.23.0 - September 17, 2019

Added: Support for TrainerRoad outdoor planned workouts

Added: Support for iOS 13

Fixed: ELEMNT MINI workout transfers

Fixed: Duplicate uploads to Training Peaks

Fixed: Workouts not being removed after deleting from the app

Removed: Option to login with Facebook

Note: This will be the last version to support iOS 10

ELEMNT App for iOS 1.22.0 - September 3, 2019

Stability improvements

ELEMNT App for iOS 1.21.0 - August 26, 2019

Added: Support for ANT+ radar sensors

Fixed: Issue with selected routes not being visible on map of the Workout page

Fixed: Issues with setting wheel circumference on speed sensors

Fixed: Unable to create custom pages on ELEMNT MINI

Fixed: Crash when viewing some types of Planned Workouts

Fixed: Unable to configure 12 speed electronic drivetrains

ELEMNT App for iOS 1.20.0 - August 13, 2019*

Fixed: Workout page not displaying loaded routes

Fixed: ROAM showing as connected in Settings even when disconnected

Fixed: Planned workout chart disappearing

Fixed: Sensors showing connected after being unpaired

Fixed: Apple Health uploads containing gross time (including pauses) instead of net time

Improved: Enabled Strava authentication through the Strava mobile app

*This release will roll out slowly to select users until full distribution on August 20, 2019.

ELEMNT App for iOS 1.19.1 - August 6, 2019

Bug fixes and miscellaneous improvements

ELEMNT App for iOS 1.19.0 - July 11, 2019*

FIXED: Strava sharing issues

FIXED: Profile set to default power and heart rate zones when creating an account

FIXED: Heart rate zones resetting to default

FIXED: Crashes when syncing ride file with muscle oxygen data

FIXED: User weight failing to save in profile

FIXED: Various crash fixes

Improved: Live tracking

*This release will roll out slowly to select users until full distribution on July 18, 2019.

ELEMNT App for iOS 1.18.0 - June 5, 2019

Added: Strava Live Segments customization page

Added: Strava Live Segment data fields now available on other pages

FIXED: Data fields do not indicate a selection when setting up a custom page

FIXED: Bug causing backlight timeout value to change

FIXED: Crashes related to WiFi connection and planned workouts

FIXED: BestBikeSplit users not seeing Target Power

FIXED: Workouts showing an old date/time

FIXED: Uploads to Xert and MapMyTracks

ELEMNT App for iOS 1.17.1 - May 15, 2019

FIXED: Data field and page configuration bugs

FIXED: HR zone reset bug

FIXED: Lost connection after a firmware update

FIXED: Bug with live track summary not matching FIT file

ELEMNT App for iOS 1.17.0 - May 1, 2019

FIXED: Routes not updating via Bluetooth

FIXED: Unable to set wheel circumference for Elite Drivo Trainer

FIXED: Inability to set crank length for pedal power meters

ELEMNT App for iOS 1.16.1 - April 23, 2019

FIXED: Creation of routes from history

FIXED: Issue setting up custom pages for MINI

FIXED: Improper route sorting on workout tab

FIXED: Workout details and map missing in ELEMNT app

FIXED: Various small bug fixes and stability improvements

ELEMNT App for iOS 1.16.0 - April 15, 2019

All new look & feel!

Account login & profile sync

New route sync with MTB Project and Singletracks!

More workout sharing partners: Map My Tracks, Xert, and Final Surge

Total odometer in the ELEMNT app

Improved support for multiple ELEMNTs

Support for cadence targets from TrainingPeaks planned workouts

ELEMNT App for iOS 1.15.2 - December 5, 2018

FIXED: potential crash related to displaying charts in workout details

FIXED: bug when transferring planned workouts

ELEMNT App for iOS 1.15.1 - November 7, 2018

FIXED: Sync of Strava private routes

FIXED: Power curve not displaying

ELEMNT App for iOS 1.15.0 - October 1, 2018

This release centers around integration with the Pioneer Pedaling Monitor System.

ADDED: Integration with the Pioneer Pedaling Monitor System

FIXED: "Take Me To" routing option now excludes ferries

FIXED: Bug causing TCX and GPX file import failures

ELEMNT App for iOS 1.14.6 - August 6, 2018

FIXED: Various app crashes when paired with ELEMNT/BOLT

FIXED: Additional issues surrounding Komoot routes

FIXED: Strava live relative effort data field not populating

FIXED: Workouts not registering as "finished" in the app

FIXED: "Take Me To" automatically reversing route

FIXED: ELEMNT/BOLT stuck loading on configuration screen

ELEMNT App for iOS 1.14.5 - July 18, 2018

FIXED: ELEMNT MINI display configuration error

FIXED: Incorrect TSS calculation

FIXED: Power meter sensor displaying option to set Wheel circumference

FIXED: ELEMNT not reconnecting to app after being forgotten in iOS settings

ADDED: Integration with SRAM TyreWiz

Strava Live Relative Effort

FIXED: Duplicate uploads to third parties

ELEMNT App for iOS 1.14.3 - June 13, 2018

FIXED: Bug causing data to not be transferred to the ELEMNT app

FIXED: Inconsistency with first value displayed on the power training profile screen

FIXED: Bug causing non-structured workouts to be synced from Training Peaks

FIXED: Bug preventing sharing of lap data to Cycling Analytics

FIXED: Bug causing mixed units to reset

FIXED: MINI display configuration error

FIXED: Strava share bug

FIXED: Bug causing green success sharing checkmarks to disappear after reopening app

FIXED: Bugs causing UI issues with text placement

Translation and typo corrections

Crash fixes

ELEMNT App for iOS 1.14.2 - April 2, 2018

Fixes crash when using non-ASCII characters in a custom page name

ELEMNT App for iOS 1.14.1 - March 27, 2018

Fixed: Strava sharing

Fixed: Mixed units resetting

ELEMNT App for iOS 1.14.0 - March 19, 2018

Improved the ascent/descent accumulation algorithm when riding slowly

AdjustedGPS accuracy limits to reduce GPS dropouts

Improved ELEMNT app synchronization with ELEMNT over Bluetooth

Bug fixes and other improvements

ELEMNT App for iOS 1.13.3 - January 8, 2018

Fixed: Detailed results always show in kilometers

Fixed: App update disables live tracking

Fixed: Results charts displaying as empty

Fixed: Issue that was causing sensor firmware to not update

Fixed: Some German translations

Fixed: Issue with manually importing GPX routes not showing elevation

Fixed: Could not set gear ratio for Shimano Di2

Fixed: DropBox sharing issue

Fixed: MINI workout sync fail

Fixed: Power chart does not display pedal smoothness & torque effectiveness

Fixed: AVG HR (Last lap) showing AVG HR (Lap)

Added support for TICKR FIT

Added support for 2peak sharing

Added TBT tutorial page

ELEMNT App for iOS 1.13.2 - December 11, 2017

Various crash fixes

ELEMNT App for iOS 1.13.1 - November 27, 2017

Various crash fixes

ELEMNT App for iOS 1.13.0 - November 20, 2017

Fixed: Dropbox export gets stuck

Fixed: Route not shown on Live Track site when route is selected on ELEMNT

Fixed: MINI elevation not getting calibrated

Fixed: ELEMNT app crashing on iPhone 4S iOS 9.3.5 when importing routes

Fixed: Mixed units are being reset

Fixed: After ride the ride map for last ride on results tab is blank=

Added support for iPhone X

Upgraded maps

For iPhone/iOS, please see ELEMNT App Updates (iOS)

ELEMNT App for Android 1.25.0.65 - November 12, 2019*

Added: Relive sharing support

Added: Updated the in-app maps

Fixed: Difficulties reconnecting ELEMNT after connection loss

Fixed: App stability issues on Android 5.1

Note: This will be the last update to support Android 5.1. Future app updates will require Android 6 or newer.

*This release will roll out slowly to select users until full distribution on November 19, 2019.

ELEMNT App for Android 1.24.0.34 - November 6, 2019

Bug fixes

ELEMNT App for Android 1.24.0.22 - October 2, 2019*

Additional stability improvements

Improved map download process

*This release will roll out slowly to select users until full distribution on October 9, 2019.

ELEMNT App for Android 1.23.0.25 - September 24, 2019*

Additional stability improvements

*This release will roll out slowly to select users until full distribution on October 1, 2019.

ELEMNT App for Android 1.23.0.21 - September 19, 2019

Stability improvements

ELEMNT App for Android 1.23.0.17 - September 17, 2019

Added: Support for TrainerRoad outdoor planned workouts

Removed: Option to login with Facebook

Stability improvements

ELEMNT App for Android 1.22.0.21 - September 3, 2019

Fixed: ELEMNT MINI custom pages not saving correctly

ELEMNT App for Android 1.21.0.26 - August 29, 2019

Fixed: Phone connectivity issue with head units over Bluetooth

ELEMNT App for Android 1.21.0.22 - August 26, 2019

Added: Support for ANT+ radar sensors

Fixed: Phones not re-connecting after connection loss

ELEMNT App for Android 1.20.0.36 - August 20, 2019

Stability improvements

ELEMNT App for Android 1.20.0.34 - August 13, 2019*

Fixed: Missing toggle to Show Elevation Profile on the map page (Settings > Customize Pages > Map)

Fixed: Data field issues on map page

*This release will roll out slowly to select users until full distribution on August 20, 2019.

ELEMNT App for Android 1.19.0.38 - July 31, 2019

Bug fixes and miscellaneous improvements

ELEMNT App for Android 1.19.0.34 - July 9, 2019*

Stability improvements

*This release will roll out slowly to select users until full distribution on July 16, 2019.

ELEMNT App for Android 1.18.0.34 - June 26, 2019

FIXED: Receiving notifications without a contact name or phone number

FIXED: Workouts not uploading to the ELEMNT app

FIXED: Various stability improvements

ELEMNT App for Android 1.18.0.25 - June 5, 2019

Added: Ability to customize Strava Live Segments page

Added: Ability to add Strava Live Segment data fields to other pages

FIXED: Onboarding redisplaying on app launch

FIXED: Display configuration resets after an update

FIXED: Localization (translation) updates

ELEMNT App for Android 1.17.1.2 - May 14, 2019

FIXED: Buttons on firmware update screen not working

FIXED: Status shown as unknown" when returning to on-boarding firmware update screen

Improved on-boarding for ROAM users

ELEMNT App for Android 1.17.0.65 - May 1, 2019

Various on-boarding improvements

FIXED: various on-boarding bugs

ELEMNT App for Android 1.16.0.217 - April 15, 2019

All new look & feel!

Account login & profile sync

New route sync with MTB Project and Singletracks!

More workout sharing partners: Map My Tracks, Xert, and Final Surge

Total odometer in the ELEMNT app

Improved support for multiple ELEMNTs

Support for cadence targets from TrainingPeaks planned workouts

ELEMNT App for Android 1.15.0.275 - December 19, 2018

FIXED: Issue where routes could not be imported from WhatsApp

ELEMNT App for Android 1.15.0.265 - November 7, 2018

FIXED: ELEMNT/BOLT now updates edited Komoot routes on Bluetooth sync

FIXED: Sync of Strava private routes

ELEMNT App for Android 1.15.0.224 - October 1, 2018

This release centers around integration with the Pioneer Pedaling Monitor System.

ADDED: Integration with the Pioneer Pedaling Monitor System

FIXED: "Take Me To" routing now excludes ferries

FIXED: Inability to disable "include zeros" from power and cadence data fields

UPDATED: Japanese translations

ELEMNT App for Android 1.14.5.34 - August 14, 2018

FIXED: Issue with uploads to specific third party apps

ELEMNT App for Android 1.14.5.32 - July 18, 2018

FIXED: Cycling Analytics account link

FIXED: Crash while viewing RIDE tab during a ride

ADDED: Integration with SRAM TyreWiz

Strava Live Relative Effort

FIXED: Duplicate uploads to third parties

ELEMNT App for Android 1.14.0.25 - June 3, 2018

FIXED: 'Take me to' feature unable to search for specific addresses

FIXED: Ability to enable automatic uploads not working

FIXED: MapBox crash when changing pages

ELEMNT App for Android 1.14.0.20 - March 19, 2018

FIXED: 'Take Me There' returning incorrect search results

FIXED: App crash when tapping on 'NEW' from Planned workouts menu

FIXED: App crash when tapping on old workout from Results tab

FIXED: App crash if looking at previous workout while riding

FIXED: Cannot create routes from previous workouts

FIXED: Some Dutch translations

ELEMNT App for Android 1.13.2.7 - January 10, 2017

Switched maps to Mapbox

Minor bug fixes

ELEMNT App for Android 1.13.1.0 - November 29, 2017

Various crash fixes

ELEMNT App for Android 1.13.0.13 - November 23, 2017

FIXED: Lap data showing same values for different data fields

FIXED: Power zone number changes not persisting

FIXED: HR Zone showing "this is a test" when selected

FIXED: GPX file import failing

FIXED: Lap avg speed shows max speed in workout summary

FIXED: ELEMNT MINI climbing page results do not display

FIXED: Cannot enter decimal point for auto lap distance

FIXED: Unable to rename custom pages

ADDED: FTP max upped to 400

Registering you new Wahoo trainer is the best way to make sure you receive all promotional offers included with your purchase. Once registered, you will receive an email with any applicable promo codes. Please be aware, the trainer must be connected to the Wahoo app via Bluetooth while logged into a Wahoo cloud account in order to complete registration (trainer registration is not supported over ANT+ connections).

Make sure Bluetooth is on and open the Wahoo app downloaded fromthe Apple App Store (iOS) or Google Play store (Android).

Open the Profile page and ensure you're logged in to your Wahoo Cloud account.

With your trainer powered on, navigate to the Workout or Settings page and edit or set up Linked Sensors to select your trainer from the list. Once the trainer is saved to a logged in Wahoo Cloud account, registration is complete.

General Thru Axle Compatibility:

Though the KICKR SNAP is compatible with most bikes as described in the KICKR SNAP Bike Compatibility Guide, select Thru Axle bikes may be incompatible due to the design of the dropouts or rear derailleur.:

contact support

The style of dropouts on this Santa Cruz bike prohibits the adapter from protruding into the clamp which secures the frame.Image credit: pinkbike.com

Bikes with a closed or capped dropout on the the drive side (as pictured above) are incompatible since they prohibit KICKR SNAP from clamping to and securing the exterior of the frame (and dropouts). If a thru axle bike is unable to support an extended thru axle and cap as included in the KICKR SNAP Thru Axle Adapter, it is unlikely to be compatible with KICKR SNAP.

Known Incompatible Bikes:

Some Santa Cruz bikes

Some Trek bikes including Domane variants

To fully ensure compatibility, please visit a local Wahoo Fitness retailer to test your bicycles fit or before purchasing.

Wahoo Smart Trainerswill work out of the box with several apps. If you know of one that is not currently listed, please let us know!

Wahoo Fitness AppWahoos App controls the KICKR in four different ways

Level mode:Weve built 10 levels, each with a progressive resistance curve, just like riding outside. For example, the faster you pedal, the harder it gets simulating rolling and air resistance.

Erg mode:With the KICKR, you can set a target wattage and the KICKR will remain at that wattage as you ride independent of speed and cadence. This is the ultimate way to train with Power.

Sim mode:With sim mode, you can enter your weight, bike type, riding position, headwind, and grade and the KICKR will accurately model the power curve just as if you were riding outdoors.

Resistance mode:For those of you who need to be in control, this allows you to adjust resistance of the brake manually from 0 to 100%

Compatibility:Any iPhone with Bluetooth 4.0: iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 7, & 7 Plus; iPad 3 and newer. Most Android devices running Android 6.0 or newer.

ZwiftZwift is the first company to use massive multiplayer gaming technology to bring the outdoor cycling experience indoors. Athletes from around the globe can ride with each other in rich 3D generated worlds simply by connecting their existing devices (e.g. trainers, power meters, heart rate monitors, etc) wirelessly via open Industry standard ANT+ or BLE. From structured workouts and training plans to friendly competition and casual group rides, Zwift is building a community of like-minded athletes united in the pursuit of a better indoor cycling experience.Compatibility: Apple andWindows machines (with ANT+ USB stick); iPhone 5S, 6, 6 Plus, 7, & 7 Plus; iPad Air or higher.

Trainer RoadTrainer Road.com is an online community focused on providing cyclists incredible structured workouts and training programs. Check out www.trainerroad.com for more informationCompatibility:Latest generation Apple laptops and desktops with Bluetooth 4.0 built in. Older Macs and Macbooks with a BT40 dongle Windows machines (with ANT+ USB stick)

KinomapKinomap is an online sharing site of geolocated videos. Choose a video of your favorite Tour stage or race course and Kinomap will control the KICKR as you watch the video, matching the resistance to the elevation of your virtual ride. Check out trainer.kinomap.com for more information.Compatibility:Any iPhone with Bluetooth 4.0: iPhone 4S, 5, 5S, 5C, 6 & 6 Plus; iPad 3 and newer; iPod 5G and newer; iPad mini.

Any ANT+ head unitThe KICKR broadcasts speed and power (wattage) via ANT+. Any ANT+ enabled bike computer, such as a Garmin Edge, will be able to read the data from your KICKR. Any ANT+ FE-C head unit can also control the KICKR and adjust resistance.

What are the best practices for using the CLIMB?

Before you ride, always reset the CLIMB to level by double tapping the center lock mode button, then counterbalance the CLIMB (like a pendulum) by raising the handlebars until the unit is off the ground, allowing it to swing freely and come to a complete stop before setting it back down. This ensures accurate positioning with the CLIMB centered below the fork to counter any slip which might occur on a ride.

Only counterbalance the CLIMB with your fork in the "level" position by double tapping the center lock mode button.

Check mounting before each ride to ensure both the front and back skewer are properly secured to the CLIMB and KICKR.

Keep the handlebars straight during the entire ride.

Ensure your Wheel Circumference, Bike Type, and Wheelbase are properly configured for your bike from the KICKR or SNAP page in the Sensors section of the Wahoo Fitness App. See full instructions here.

Always keep the CLIMB properly centered on your bike and trainer and on a level surface. Do not use "rocker plates" or other unstable surfaces with the KICKR CLIMB as these will void the warranty and may cause serious injury or damage.

Keep your riding area clear of obstacles and debris. Ensure your bike's handlebars (and other parts) can not impact other surfaces (like the Wahoo Desk ) when in motion.

Ensure your riding surface is not slick and remains clean and free of debris. Use a mat specifically designed for trainers like the Wahoo KICKR Trainer Floormat for best results.

Always check your bike's components (especially the brakes) before riding outdoors.

While most bikes that are compatible with KICKR or SNAP are also compatible with the KICKR CLIMB, any known exceptions are listed here.

Please be aware that since it is not possible to test every bike, this is not a comprehensive list. We recommend testing your bike with the KICKR CLIMB at your local dealer, where possible, prior to purchase. Ensure there is no interaction between the bike fork and the CLIMB when raising or lowering throughout its full range of motion. Wahoo is not responsible for any damage to bikes.

The following bikes* are NOT compatible with KICKR CLIMB:

Trek Madone 2006 - 2013 with 100mm quick release or thru axle dropouts

Trek Speed Concept 2012 with 100mm quick release dropouts

Trek Lexa 2014 with 100mm dropouts

Merida Scultura 2019 with 100mm quick release dropouts

Canyon Aeroad 2014 with 100mm quick release dropouts

Trek 2.1 Series 2012

Giant Propell Disc 2018

Boardman Road Team Carbon 2018

Cube Attain GTC 2017

Some Serotta bikes

Any bike with a Cannondale Lefty fork

*Additional incompatible bikes may not be listed. This list may be amended as incompatible bikes are discovered. Always test bike compatibility at your local KICKR CLIMB dealer, where possible, before purchasing.

Auto-pause is a feature of the Wahoo Fitness App that automatically pauses your workout when you stop running or riding. To turn on auto-pause, follow these steps:

From the Wahoo Fitness home page, select "Settings".

Select the workout profile you would like to activate this feature for.

Turn the "Auto Pause When Stopped" switch 'ON'.

When auto-pause is activated, the App will flash paused to show the App is paused and will automatically resume the workout when you begin moving.

By design, the KICKR itself measures and transmits speed and power data.New KICKRs (not including the KICKR SNAP or CORE) also come with our RPM / Cadence sensor included.

Update: As of Sept. 4th, 2019, KICKR '18 models running Firmware v3.4.69 or newer and KICK CORE models running Firmware v1.0.11 or newer now support automatic cadence tracking and broadcasting over both Bluetooth and ANT+.

Additionally, other Bluetooth 4.0 (or newer) and ANT+ sensors can be paired with the Wahoo Fitness app. For heart rate, we recommend our TICKR heart rate monitors (not included).

Videos are instrumental to diagnosing many issues. The following steps demonstrate how to create a video of your trainer for submission in a support ticket.

Using iOS:

Open the iOS camera app and switch to video mode. in your ticket

Secure the iOS device to a stationary position, or have someone else either film using the iOS device or film them pedaling while recording, yourself.

Be sure to film the trainer while both pedaling and coasting/freewheeling for 15-30 seconds in total. Ensure the video is no longer than 30 seconds, since longer times may increase file size over the 20MB attachment limit.

a. If you haven't opened a ticket: visit our contact page from the device used to film and select the video from the attachment button as shown below:b. If you already have a ticket: simply attach the video in your email reply.

If your video is larger than 20MB, simply upload the video to YouTube (instructions here ) and provide the link in your ticket.

Using Android:

Open the Android camera app and switch to video mode.

Secure the Android device to a stationary position, or have someone else either film using the Android device or film them pedaling while you record.

Be sure to film the trainer while both pedaling and coasting/freewheeling for 15-30 seconds in total. Ensure the video is no longer than 30 seconds, since longer times may increase file size over the 20MB attachment limit.

a. If you haven't opened a ticket: visit our contact page from the device used to film and select the video from the attachment button as shown below:b. If you already have a ticket: simply attach the video in your email reply.

If your video is larger than 20MB, simply upload the video to YouTube (instructions here ) and provide the link .

TrainingPeaks offers detailed descriptions of Normalized Power (NP), Intensity Factor (IF), and Training Stress Score (TSS) in this article by Dr. Andy Coggan.

IMPORTANT: This page covers installation of the Campagnolo Freehub on KICKR '14 and '16.

Please see instructions for KICKR '18 and KICKR CORE if installing on these trainers.

mount your bike

Installation on KICKR '14 & KICKR '16

Required Tools:

Torque Wrench with 17mm socket (capable of 6 Nm)

17mm Wrench (optional)

Important Torque Settings:

Black Axle Nut: 6Nm

Installation Steps:

The stock freehub can be removed with or without the cassette installed. If you choose to remove the cassette prior to removing the freehub, follow these instructions: Changing the Cassette.

Remove the external black nut with the 17mm wrench. Set this aside to use again.

Remove the spacer behind the nut. Set this aside to use again.

Remove the existing freehub.

If there is a spacer remaining on the axle, remove it. Save this with the Shimano freehub you just removed.

Install the spacer that came with the Campagnolo freehub.

Remove the retaining ring from the Campagnolo freehub.

Install the freehub on the axle. Twist counter clockwise to help the pawls fall into place. You should not be able to see the pawls.

Re-install the spacer removed in step 3.

Re-install the nut removed in step 2.

Torque the nut to precisely 6Nm.

IMPORTANT: Over-torquing the nut may cause damage to the bearings. If you do not have a torque wrench, your local bike shop most certainly will!

Note: The black, rubber dust seal mentioned in the video is no longer in use. Please install the Campagnolo Freehub without this dust seal.

Installing the Cassette:

Once your freehub is installed, install your cassette on the freehub like shown in the video below (instructions start at 1:20):

You're now ready to and get KICKN!

With notifications enabled, you should receive an alert for the following:

iOS - Calls, Texts, and Emails

Android - Calls and Texts

In order to receive notifications, you must have your ELEMNT/BOLT/ROAM paired to your phone via Bluetooth. If you are still not receiving notifications as expected, check the following:

On the settings page of the ELEMNT app, check the ELEMNT status at the top of the page. Verify the ELEMNT is connected and up to date with the most recent firmware.

On the Settings page of the ELEMNT app, scroll down to the Alerts section. Ensure the toggles for all notifications you wish to receive are on. If the issue continues, toggle each off and then back on again.

Ensure all notifications you are expecting to receive are being received by the apps native to the device. You will not receive alerts for messages and emails received by third-party apps such as WhatsApp, Gmail, etc.

Verify notifications for your device's native apps are set to enabled. These can usually be found on your phone under Settings > Notifications > Messages. Try toggling these off and back on again as well, ensuring the setting is set to "always," if available.

Messages cannot be received by multiple devices. Please ensure you aren't using another Bluetooth device (such as an Apple Watch, or Garmin Vivoactive) that is set to receive messages. If so, disable messaging on the other device to receive messages on your ELEMNT.

(iOS) If the issue persists, please forget the ELEMNT/BOLT/ROAM from the phones Bluetooth settings (along with any duplicate ELEMNT entries) and the ELEMNT app, then pair to the phone again. Finally, restart your phone.

(iOS) Please verify notifications are appearing in your iOS notifications center. This is required in order for the messages to be received by the ELEMNT. If you do not see the message in the iOS notifications center, please check your iOS settings. This can also signal that messages are being received by another device.

The steps below assume you've already followed the standard steps for Pairing with the ELEMNT App. If you're still having trouble, the following tips are likely to fix your issue.

Start by checking your camera or the ELEMNT/BOLT/ROAM QR Code:

Make sure your mobile device's camera is clean and clearly focused on the ELEMNT/BOLT/ROAM

Keep the ELEMNT/BOLT/ROAM's screen clear of reflections and debris

Next try un-pairing the ELEMNT/BOLT/ROAM then re-pairing:

iOS:

First remove the ELEMNT/BOLT/ROAM from your phones Bluetooth settings with these steps:

Open the Settings App on your iOS device

Select Bluetooth

Locate the ELEMNT/BOLT/ROAM in the list of My Devices

Select the lower case i to the right of the ELEMNT/BOLT/ROAM

Select Forget This Device

Once complete, open theSettings page of the ELEMNT app to select Forget Phone, then Pair.

Note on iOS updates: Un-pairing your ELEMNT/BOLT/ROAM after an iOS update may be required to re-establish a connection following instructions to re-display the QR Code, then re-pairing to the app.

Note on iOS 13: A new prompt to allow Bluetooth for individual apps was added to this iOS version, separately from the iPhone's main Bluetooth settings. For continued pairing issues, please check the following:

Open the main iOS Settings app and scroll down to select ELEMNT

Ensure that Bluetooth Sharing is toggled on (to the right).

Android:

Choose FORGET PHONE directly from the ELEMNT/BOLT/ROAMs settings (left side button), then retry pairing.

How to Update Wahoo Smart Trainer Firmware This page contains firmware update notes for the original KICKR SNAP without external LEDs, shown above.

For firmware update notes for the new KICKR SNAP, see KICKR SNAP Firmware Updates

For update instructions, see

Original SNAP v2.3.59 - 4 October 2017

Brake model: recalculating brake strength from raw spindown results to allow for updating the brake strength model.

Brake model: improved brake strength model

FE-C: fixed error causing FE-C to send raw instead of filtered power as instantaneous power

Fixed 3rd Party Power meter support

Original SNAP v2.2.51 - 23 January 2017

Fixed an issue surrounding power/resistance spikes

ANT+ FE-C communication fixes

Added option for acceleration power in ERG mode, this will report power from the SNAP similar to a crank-based power meter

Original SNAP v2.1.4 - 12 May 2016

ANT+ FE-C Control :

The addition of ANT+ FE-C support allows the KICKR and SNAP to be controlled from any FE-Cenabled device or application, such as a Garmin bike computer

Improvements to reported power and improvements to simulation mode:Improvements to the measured power during periods of acceleration also improve the feel of the trainer when using simulation mode (for example, when using Zwift).

For the newest update notes, please see ELEMNT Firmware Updates

Updating the ELEMNT/BOLT/ROAM Firmware

Notifications for new firmware updates are displayed automatically when connected to WiFi. Alternatively, you can manually update firmware from the settings menu as shown below.

Ensure your ELEMNT/BOLT/ROAM is powered on, well charged, and connected to WiFi independently from your mobile device.

Once on the home screen, press the power button to bring up the settings menu

Help with Updates Guide

Highlight SYSTEM INFO using the right-side scroll buttons and select OPEN

Ensure you have at least 200MB of free space on the second line. If not, please delete any unused maps until 200MB of free space is available. Then, highlight CHECK FOR UPDATES and select CHECK

Follow the prompts to update the firmware and it will download and install if available.Note that automatic updates are only performed prior to powering off to avoid interference with use.

Note: Following an update, it may be necessary to re-pair your ELEMNT/BOLT/ROAM to the ELEMNT App following instructions to re-display the QR Code, then re-pairing to the app.

For persistent issues, please check the instructions in our .